ЭЛКО-ЛОГО

ELKO EKO60000 Timer Socket

ELKO-EKO60000-Timer-Socket-PRODUCT

МОДЕЛИ

ЭКО60000
ЭКО60001
ЭКО30437
ЭКО50111
ЭКО50112

Необходимые принадлежности

Insert without frame can be completed with: Рамка в соответствующем дизайне и цвете.

PKR66748-03 07/25

ELKO-EKO60000-Timer-Socket-FIG-1

Timer socket outlet

With the Timer socket-outlet, you can switch on attached loads (e.g. coffee machines, irons, etc.) for a preset time period using the installed push-button (A).

The timer socket-outlet has six selectable time delays (15 min, 30 min, 1 h, 2 h, 4 h, 8 h). After the set time has elapsed, the timer socket-outlet switches off again automatically. The timer socket-outlet can be switched off by pushing the button again before the time has elapsed. The power status of the socket-outlet is shown with the LED (B).

ELKO-EKO60000-Timer-Socket-FIG-2

  • Зеленый светодиод: Socket outlet switched on
  • Светодиод выключен: Socket outlet switched off

Check the time delay
Press the button 3 times short (<0.5 s) to find out the current time delay. The status LED shows the actual setting.

ELKO-EKO60000-Timer-Socket-FIG-3

Связь

ELKO-EKO60000-Timer-Socket-FIG-4 ОПАСНОСТЬ ПОРАЖЕНИЯ ЭЛЕКТРИЧЕСКИМ ТОКОМ, ВЗРЫВА ИЛИ ВСПЫШКИ ДУГИ

Безопасный электрический монтаж должен выполняться только квалифицированными специалистами. Квалифицированные специалисты должны подтвердить глубокие знания в следующих областях:

  • Подключение к установочным сетям.
  • Подключение нескольких электрических устройств.
  • Прокладка электрических кабелей.
  • Стандарты безопасности, местные правила и нормы электромонтажа.

Несоблюдение этих инструкций может привести к смерти или серьезным травмам.

The socket outlet is part of the building installation. The relevant standards and directives of the country must be observed during planning and construction. The operation of the device is permissible only on the 230V / 50 Hz alternating current network.

The installation may only be carried out in commercially available flush-mounted wall-boxes (installation boxes), with a minimum depth of 40mm, in accordance with EN 60670-1.

Монтаж

ELKO-EKO60000-Timer-Socket-FIG-5

Подключение

ELKO-EKO60000-Timer-Socket-FIG-6

Примечание: Не смешивайте разные типы нагрузки в управляемой розетке.

  • Do not use multiple sockets in the controlled socket.
  • Do not use for EV charging

ELKO-EKO60000-Timer-Socket-FIG-4 ОПАСНОСТЬ ПОРАЖЕНИЯ ЭЛЕКТРИЧЕСКИМ ТОКОМ, ВЗРЫВА ИЛИ ВСПЫШКИ ДУГИ

The socket is 1-pole switched. Depending on the installa-tion, voltage may be present at the other contact.
Несоблюдение этих инструкций может привести к смерти или серьезным травмам.

Установить задержку по времени
To enter the timer setup mode, press and hold the push button (A) for more than 5 seconds until the LED (B) lights up green. Place your finger so that you can see the LED.

ELKO-EKO60000-Timer-Socket-FIG-7

As soon as the device switches to setup mode, the LED (B) lights up green. When the button is released, the LED goes out. The LED flashes according to the current delay time (in the default factory setting 2 times for 30 minutes).

Примечание: In case the socket is switched on when entering setup mode, it will switch off automatically after pressing for 5 seconds.

The delay time is set according to the number of short presses of the button (A). The LED (B) flashes accordingly.

ELKO-EKO60000-Timer-Socket-FIG-8

Save the delay time

To save the selected delay time, press and hold the button (A) for 5 seconds. The LED (B) lights up green. When the button is released, the LED goes out. The LED flashes according to the current delay time.

ELKO-EKO60000-Timer-Socket-FIG-9

After 30 seconds without pressing the button, the device automatically exits the setup mode and the current delay time is not saved. The LED (B) blinks fast.

Защита устройства

Примечание: The device is equipped with temperature and overload protection. When the device is used with a high load over a long time, the protection can switch the socket off. In this case, the LED (B) blinks fast in red. After the device has cooled down, it is possible to switch back to normal mode. To clear the alarm, press and hold the push button for 5 seconds. After 5 seconds, the blinking will stop and the alarm will be cleared. You can use the socket outlet again.

Технические данные

ELKO-EKO60000-Timer-Socket-FIG-10

ELKO-EKO60000-Timer-Socket-FIG-11 Утилизируйте устройство отдельно от бытовых отходов в официальных пунктах сбора. Профессиональная переработка защищает людей и окружающую среду от возможных негативных последствий.

Schneider Electric Industries SAS 35, улица Жозефа Монье
FR – 92500 Рюэй-Мальмезон
elko.no/contact

PKR66748-03 07/25

Документы/Ресурсы

ELKO EKO60000 Timer Socket [pdf] Руководство по эксплуатации
EKO60000, EKO60001, EKO30437, EKO50111, EKO50112, EKO60000 Timer Socket, EKO60000, Timer Socket, Socket

Ссылки

Оставьте комментарий

Ваш адрес электронной почты не будет опубликован. Обязательные поля отмечены *