Home › ATOMSTACK › ATOMSTACK L2 Smart Z-Axis Module Installation Guide

Руководство по установке интеллектуального модуля оси Z ATOMSTACK L2

ATOMSTACK-L2-Smart-Z-Axis-Module-featured-image

ATOMSTACK L2 Интеллектуальный модуль оси Z

Руководство по установке автоматического регулятора высоты по оси Z L2-5W/L2-10W/L2-20W/L2-40W

Примечание: Изображения предназначены только для справки, пожалуйста, обратитесь к реальному продукту. Для получения дополнительной информации отсканируйте QR-код.

список

Метод установки оси Z

А5 ПРО В2/А10 ПРО В2

Отвинтите 4 шт. M4*6 против часовой стрелки, чтобы снять ползунок.

Установите специальный разъем A5 Pro V2/A10 Pro V2.
Затяните 4 шт. M4*6

А20 ПРО В2/А40 ПРО В2

A6 Pro / A12 Pro / A24 Pro / X12 Pro / X24 Pro / E6 Pro / E18 Pro / E24 Pro / A6 Ultral / A12 Ultral / A24 Ultral / X12 Ultral / X24 Ultral A48 PRO/A48 Ultra нет необходимости перемещать концевые выключатели

Шаг 1

Переверните гравер
Отверните 2 винта с платы концевого выключателя.
Переместите доску вперед, чтобы совместить 2 отверстия.
Зафиксируйте 2 винта обратно на плату.
Заканчивать
Переверните гравер

Лазерный унифицированный метод установки

Шаг:1 Снимите 4 шт. M3 и лазерный слайдер.
Шаг:2 Установите лазерный слайдер, используя 4 винта M3, снятые на этапе 1.

Примечание: Отвинтите сначала крепежный элемент с крестовой отверткой из набора инструментов, затем установите лазерный слайдер на лазер A48.

Способ подключения кабеля

Лазерный метод установки
A5 PRO V2/A10 PRO V2/A20 PRO V2/A40 PRO V2

A6 Pro / A12 Pro / A24 Pro / X12 Pro / X24 Pro / E6 Pro / E18 Pro / E24 Pro / A6 Ultral/ A12 Ultral/A24 Ultral/X12 Ultral/ X24 Ultral

A5 PRO V2/A10 PRO V2/A20 PRO V2/A40 PRO V2

Примечание: При включении питания для использования автоматической регулировки высоты по оси Z вам нужно всего лишь нажать кнопку «автофокусировка» на блоке управления, чтобы автоматически сфокусировать лазер.

A6 Pro / A12 Pro / A24 Pro / X12 Pro / X24 Pro / E6 Pro / E18 Pro / E24 Pro / A6 Ultral / A12 Ultral / A24 Ultral / X12 Ultral / X24 Ultral

Примечание: Дисплей необходим при использовании автоматического регулятора высоты по оси Z, вам необходимо управлять им со стороны дисплея.

Обслуживание клиентов: Для получения подробной гарантийной политики, пожалуйста, посетите наш официальный webсайт : www.atomstack.com По вопросам технической поддержки и обслуживания обращайтесь по электронной почте: support@atomstack.com
Производитель: Шэньчжэньская компания AtomStack Technologies Co., Ltd.
Адрес: 17-й этаж, корпус 3А, фаза II, Интеллектуальный парк, № 76, проспект Баохэ, Bip-код: tret, район Лунган, Шэньчжэнь, Гуандун, Китай
Сканировать QR-код: ИЛИ считыватель кодов/сканер штрих-кодов или любое приложение со сканером

Документы/Ресурсы

L2 Интеллектуальный модуль оси Z

Installation Guide · L2, L2 Smart Z-Axis Module, Smart Z-Axis Module, Z-Axis Module, Module

Ссылки

Руководство пользователяmanual.tools

Published: July 13, 2024

Обновлено: 14 июля 2024 г.

Вопросы и ответы

Helpful product questions tied to this manual. Each item links to the full Q&A page.

Вопросы и ответы

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

🇺🇸 Robert говорит:

23 апреля 2026 г. в 12:48
I have an ATOMSTACK A20 PRO V2 machine and have just purchased a L2 Z axis motorized drive ( BM AAS41A0125-AB ) and would like to hook it up but the cable attached to the unit has a connector which does not match any place on my machine . Where does it go to . In the instructions it looks like where the connection for the y motor is. Please clarify how to hook it up . Thank You Bob
🇺🇸 Robert asks I have an ATOMSTACK A20 PRO V2 machine and have just purchased a L2 Z axis motorized drive ( BM AAS41A0125-AB ) and would like to hook it up but the cable attached to the unit has a connector which does not match any place on my machine . Where does it go to . In the instructions it looks like where the connection for the y motor is. Please clarify how to hook it up . Thank You Bob

Manuals+ clarified question

Вопрос

How do I connect the L2 Smart Z-Axis Module cable to an ATOMSTACK A20 PRO V2 machine?
Отвечать

Для подключения ATOMSTACK L2 Интеллектуальный модуль оси Z к вашему А20 ПРО V2, you must use the specific wiring method outlined in the manual for "V2" series machines. The connection does not plug directly into a spare port on the motherboard; instead, it typically involves an adapter or a specific bridge connection.

Согласно Section 05 — Cable connection method for the A20 PRO V2:

X-Axis Connection: The Z-axis module cable usually connects to the transfer board located on the X-axis carriage.

Y-Axis Motor Comparison: While the connector may look similar to a Y-axis motor plug, it is intended for the Z-axis control port. On V2 models, this is often a 4-pin or 6-pin connector located on the breakout board near the laser module mount.

Check for the Adapter: Ensure you are using the "Z-axis connection cable" included in the L2 kit (listed as item 4 in the 01-List). One end connects to the L2 module motor, and the other connects to the reserved Z-axis port on the machine's X-axis terminal.

If the connector physically does not fit any port on the X-axis carriage board, please verify if your kit included a small плата адаптера или Y-shaped splitter cable, as some V2 revisions require splitting the signal or using a specific conversion interface provided in the L2 box.
Read the full Q&A page
Отвечать
1. 🇺🇸 Robert говорит:
  
  23 апреля 2026 г. в 2:31
  I don’t know what the transfer board is nor do I see anything on the x axis carriage. What is the x axis terminal ? I don’t see any extra ports anywhere .
  🇺🇸 Robert asks I don't know what the transfer board is nor do I see anything on the x axis carriage. What is the x axis terminal ? I don't see any extra ports anywhere .
  
  Manuals+ clarified question
  
  Вопрос
  
  Where are the transfer board and X-axis terminal located on the ATOMSTACK L2 Smart Z-Axis Module?
  
  Отвечать
  
  Based on the installation manual for the ATOMSTACK L2 Интеллектуальный модуль оси Z, the components you are looking for are part of the cable connection setup (Section 05):
  
  Transfer Board: This is the small PCB (circuit board) located on the back or side of the X-axis carriage (the part that moves left and right). On many AtomStack models like the A6, A12, A24, and X24 series, this board is where the main ribbon cable connects.
  
  X-axis Terminal: This refers to the specific port on that transfer board. For the L2 module, you typically need to plug the Z-axis connection cable into the port labeled for the Z-axis or the auxiliary port on this board.
  
  Примечание: If you do not see extra ports, ensure you are looking at the назад of the laser carriage assembly. On some older models (like the A5 Pro or V2 series), the connection method differs and may involve connecting directly to the main control box or using a specific adapter cable included in the L2 kit. Please verify your specific machine model, as the manual shows different wiring paths for the A5/V2 series versus the Pro/Ultra series.
  
  Read the full Q&A page
  Отвечать
  1. 🇺🇸 Robert говорит:
    
    23 апреля 2026 г. в 2:55
    I do not see any PCB or any extra ports. Nor is there any adapters or splitters in the box.
    
    🇺🇸 Robert asks I do not see any PCB or any extra ports. Nor is there any adapters or splitters in the box.
    
    Manuals+ clarified question
    
    Вопрос
    
    Where are the PCB, extra ports, adapters, or splitters for the ATOMSTACK L2 Smart Z-Axis Module?
    
    Отвечать
    
    Based on the ATOMSTACK L2 Smart Z-Axis Module installation guide, the components included in the box (Section 01 - List) are:
    
    Z-axis height adjuster
    
    Laser slider
    
    A5/P/A10/A20/X20/S20 dedicated connector
    
    Винты M3 * 6
    
    Винты M4 * 5
    
    Z-axis connection cable
    
    Руководство
    
    Шестигранный ключ 2.0/2.5
    
    Крестовая отвертка
    
    Regarding the PCB and Ports: The L2 module is designed to integrate with existing AtomStack frames. For many models (like the A6 Pro, A12 Pro, A24 Pro, etc.), the connection is made directly to the existing X-axis motor interface or the laser module's connection point using the provided Z-axis connection cable. There is typically no separate external PCB board included in this kit.
    
    Regarding Adapters/Splitters: The manual shows that for certain models (Section 05 - Cable connection method), you must unplug the original X-axis motor cable and connect it to the Z-axis module's interface, or use the dedicated connector provided in the kit. If your specific machine model is not listed in the manual (A5, A10, A20, A6 Pro, etc.), you may require a specific adapter not included in the standard L2 package. If these items are missing from your specific kit, it is recommended to contact support@atomstack.com для проверки.
    
    Read the full Q&A page
    Отвечать
    1. 🇺🇸 Robert говорит:
      
      23 апреля 2026 г. в 3:23
      
      Now what do I do ?
      
      🇺🇸 Robert asks Now what do I do ?
      
      Manuals+ clarified question
      
      Вопрос
      
      What are the next steps after installing the ATOMSTACK L2 Smart Z-Axis Module?
      
      Отвечать
      
      Once you have physically mounted the ATOMSTACK L2 Smart Z-Axis Module and connected the cables as shown in the manual, you must configure your software to recognize the new hardware. Follow these steps:
      
      Проверка кабеля: Ensure the Z-axis connection cable is securely plugged into the module and the corresponding port on your laser engraver's motherboard (refer to Section 05 of the manual for your specific model).
      
      Конфигурация программного обеспечения: Open your laser control software (LightBurn or LaserGRBL). You may need to enable the Z-axis in the device settings. In LightBurn, go to Настройки устройства and ensure 'Enable Z-Axis' is toggled on.
      
      Фокусировка: The L2 module is designed for automatic or simplified focusing. Use the control panel or software commands to move the Z-axis up and down to verify smooth movement before starting a project.
      
      Концевые выключатели: If you are using models like the A6 Pro, A12 Pro, or A24 Pro, the manual notes that you do not need to relocate the limit switches.
      
      If the module is not moving, double-check that the 2-pin or 4-pin connectors are not reversed and that your machine's firmware is up to date.
      
      >
      
      Read the full Q&A page
      
      Отвечать