1. Введение
This manual provides detailed instructions for the proper installation, operation, and maintenance of the GODIYMODULES High Voltage DC Converter Module Board. This module is designed to provide stable high voltage DC and filament voltage, suitable for applications such as powering Nixie tubes and Magic Eye tubes.
Изображение 1.1: Сверху вниз view of the GODIYMODULES High Voltage DC Converter Module Board. This image shows the overall layout of the components, including capacitors, inductors, the DC input jack, and the terminal blocks for input and output connections.
2. Информация по технике безопасности
WARNING: This module generates high voltage. Improper handling can result in electric shock, injury, or damage to equipment. Always exercise extreme caution when working with high voltagэлектронные схемы.
- Ensure the power supply is disconnected before making any connections or adjustments.
- Do not touch any components on the board when power is applied.
- Use appropriate insulation and safety equipment.
- Перед подачей питания убедитесь в правильности всех соединений.
- This module is intended for experienced electronics hobbyists and professionals.
3. Особенности
- Designed for Nixie and Magic Eye Tube anode and filament power supply.
- Регулируемая высокая громкостьtage DC output.
- Dedicated 6.3V filament voltagе вывод.
- Compact board design.
4. Технические характеристики
| Параметр | Ценить |
|---|---|
| Vol входtage | Постоянный ток 9В-12В |
| DC Socket Specification | 5.5*2.1 mm (Inner Positive, Outer Negative) |
| Высокая громкостьtage Выход | DC 150V-280V / 15mA (Adjustable) |
| Объем нитиtage Выход | DC 6.3V / 1500mA |
| Размеры | Приблизительные размеры упаковки: 5.24 x 3.82 x 1.34 дюймов. |
| Масса | Примерно 0.634 унции |
| Материал | Металл, Пластик |
5. Настройка и подключение
Follow these steps to correctly connect the High Voltage DC Converter Module Board to your system. Ensure all power is disconnected before proceeding.
5.1 Подключение входного питания
The module accepts a DC input voltage between 9V and 12V. There are two methods for providing input power:
- Разъем питания постоянного тока: Use a DC power adapter with a 5.5*2.1 mm plug. The plug must be inner positive and outer negative.
- Терминальный блок: Connect your DC 9V-12V power supply to the designated input terminals on the green screw terminal block. Observe correct polarity.
Image 5.1: Connection diagram showing input and output terminals. The DC 9-12V input can be connected via the barrel jack (5.5*2.1mm, inner positive, outer negative) or the screw terminal block. The image also indicates the output voltage regulation potentiometer.
Image 5.2: Detailed connection diagram illustrating the input power options (DC 9-12V via barrel jack or screw terminals) and the output connections for 6.3V filament voltage, GND, and adjustable DC 150-280V. The output voltage adjustment potentiometer is also clearly marked.
5.2 Выходные соединения
The module provides two main outputs via the green screw terminal block:
- DC 150V-280V Output: Это высокая громкостьtage output, adjustable via the onboard potentiometer. Connect the anode of your Nixie or Magic Eye tube to this output.
- Выход постоянного тока 6.3 В: This output provides 6.3V for tube filaments. Connect the filament of your tube to this output.
- Земля: Common ground connection for both outputs.
Ensure all connections are secure and correctly polarized before applying power.
6. Инструкция по эксплуатации
6.1 Включение
Once all connections are verified and secure, connect the DC 9V-12V power supply to the module. The module will immediately begin generating the output voltagес.
6.2 Adjusting High Voltage Выход
Высокий уровень громкостиtage output (DC 150V-280V) is adjustable using the blue potentiometer located on the board. Use a small screwdriver to carefully turn the potentiometer:
- Поворот по часовой стрелке воля увеличивать выходной объемtage.
- Поворот против часовой стрелки воля снижаться выходной объемtage.
Always use a multimeter to measure the output voltage while adjusting to prevent over-voltage damage to your connected components.
Изображение 6.1: Верх view of the module, clearly showing the blue potentiometer used for adjusting the high voltagе вывод.
7. Техническое обслуживание
The GODIYMODULES High Voltage DC Converter Module Board is designed for reliable operation and requires minimal maintenance.
- Содержите модуль в чистоте и не допускайте попадания на него пыли и мусора.
- Для предотвращения перегрева обеспечьте надлежащую вентиляцию вокруг модуля.
- Избегайте воздействия влаги на модуль или экстремальных температур.
- Regularly inspect connections for looseness or corrosion.
8. Поиск Неисправностей
- Нет выходного томаtage:
- Verify the input power supply is connected and providing 9V-12V DC.
- Check the polarity of the input DC power plug (inner positive, outer negative).
- Ensure all output connections are secure.
- Неправильный выходной уровень громкостиtage:
- Для высокого объемаtage output, adjust the potentiometer as described in Section 6.2.
- Use a multimeter to accurately measure the output voltagес.
- Обеспечьте входной объемtage является стабильным и находится в пределах указанного диапазона.
- Перегрев модуля:
- Обеспечьте достаточную циркуляцию воздуха вокруг модуля.
- Verify that the load connected to the outputs does not exceed the specified current limits (15mA for HV, 1500mA for 6.3V).
9 Поддержка
For further assistance or technical inquiries, please refer to the seller's contact information on the product purchase page or visit the GODIYMODULES official support channels.
