1. Важные предупреждения о безопасности.
WARNING: THIS ESC IS NOT A TOY. It is a high-power electronic component for use by knowledgeable hobbyists. Misuse can cause property damage, personal injury, or fire. NEVER short-circuit the battery terminals (+ and -). This will cause extreme heat, fire, or explosion. DISCONNECT the battery immediately after use.
Always ensure proper ventilation around the ESC during operation. Do not operate the ESC in wet conditions. Read this manual completely before installation and operation.
2. Знакомство с продуктом
The ZTW Mantis Slim G2 15A Electronic Speed Controller (ESC) is designed for micro to small-sized RC airplanes and drones. It features a compact and lightweight design, providing reliable and efficient power delivery for various flight applications, including F3P, 3D, and 4D flying. This ESC incorporates advanced technology for smooth operation and multiple protection features to ensure safety and longevity.
Image 1: ZTW Mantis Slim G2 15A ESC showing the product label and wire connections.
3.Основные характеристики
- High-Efficiency 15A Output: Delivers a continuous 15A current for stable performance.
- Integrated 5V/3A Switching BEC: Provides clean, stable power to the receiver and servos, preventing brown-outs.
- Сверхкомпактная и легкая конструкция: Allows for easy installation in tight spaces, maintaining optimal model balance.
- Comprehensive Protection Suite: Включает низкий уровень громкостиtage Cutoff (LVC) and Over-Heat protection to prevent damage.
- Smooth Operation & Wide Compatibility: Offers smooth throttle response and is compatible with 2-4S LiPo battery setups and various sensorless brushless motors.
- Программируемый: Supports programming via transmitter or ZTW LCD programming card (sold separately).
4. Технические характеристики
| Параметр | Ценить |
|---|---|
| Модель | ZTW Mantis Slim G2 15A |
| Постоянный ток | 15А |
| Пиковый ток | 30А |
| Vol входtage | 2-4S LiPo / 5-12NC |
| Тип БЭК | Switching BEC |
| Выход BEC | 5В / 3А |
| Масса | 10 г (0.32 унции) |
| Размеры (Д*Ш*В) | 25.5*15*5 мм (1 x 0.59 x 0.2 дюйма) |
| Штекер аккумулятора | JST Female |
| Штекер двигателя | 2.0mm Bullet |
| Способ программирования | Transmitter / ZTW LCD Program Card G2 |
5. Настройка и установка
Follow these steps for proper installation of your ZTW Mantis Slim G2 15A ESC:
- Подключить к двигателю: Connect the three motor wires from the ESC to the three wires of your brushless motor using the 2.0mm bullet connectors. The order of connection may affect motor rotation direction; if the motor spins in the wrong direction, swap any two of the motor wires.
- Подключиться к приемнику: Plug the servo lead (signal cable) from the ESC into the throttle channel of your RC receiver. This is typically channel 3.
- Подключение к аккумулятору: Connect your 2-4S LiPo battery (or 5-12NC battery) to the JST female connector on the ESC. Ensure correct polarity.
- Secure the ESC: Mount the ESC securely in your aircraft, ensuring good airflow for cooling. Avoid placing it near sources of interference.
Изображение 2: оконченоview of the ZTW Mantis Slim G2 15A ESC showing all connection points: battery (JST), receiver (servo lead), and motor (bullet connectors).
6. Инструкция по эксплуатации
6.1 Калибровка диапазона дроссельной заслонки
For optimal performance, calibrate the ESC's throttle range with your transmitter:
- Turn on your transmitter and set the throttle stick to its maximum position (100% throttle).
- Подключите аккумулятор к регулятору скорости. Регулятор скорости издаст серию звуковых сигналов.
- When you hear the confirmation beeps (usually a long beep or a specific tone sequence), move the throttle stick to its minimum position (0% throttle).
- The ESC will emit another series of beeps to confirm the minimum throttle position. The calibration is now complete.
6.2 Режимы программирования
The ZTW Mantis Slim G2 15A ESC supports two main operating modes:
- Только вперед: Standard mode for fixed-wing aircraft.
- Вперед и назад: For specific 3D/4D flying applications where reverse thrust is required.
Programming can be done via your transmitter's stick commands or more conveniently with the ZTW LCD Program Card G2 (sold separately). Refer to the program card's manual for detailed instructions on adjusting parameters such as battery type, cutoff voltage, timing, and brake settings.
7. Техническое обслуживание
- Поддерживайте регулятор скорости в чистоте, избегая попадания пыли, грязи и влаги.
- Регулярно проверяйте все провода и разъемы на наличие повреждений или ослабленных соединений.
- Ensure adequate airflow around the ESC to prevent overheating, especially during prolonged use.
- Храните ESC в сухом, прохладном месте, когда он не используется.
8. Поиск Неисправностей
If you encounter issues with your ESC, consider the following:
- Двигатель не вращается: Check all connections (battery, motor, receiver). Ensure the throttle is calibrated correctly. Verify the battery is charged.
- Erratic motor behavior/stuttering: This could indicate incorrect motor timing, a loose connection, or a damaged motor/ESC. Check connections and try adjusting motor timing if programmable.
- Перегрев регулятора скорости: Ensure sufficient airflow. Check for excessive current draw from the motor or an undersized propeller.
- No power to receiver/servos: Check the BEC output. Ensure the ESC is properly connected to the receiver.
- ESC beeps continuously: Это часто указывает на низкий уровень громкости.tage cutoff or an error code. Refer to the programming card manual for specific beep codes if available.
If problems persist, contact ZTW customer support for further assistance.
9. Гарантия и поддержка
For warranty information and technical support, please refer to the official ZTW webна сайте или обратитесь к продавцу. Сохраните чек на случай предъявления гарантийных претензий.
