Инструкция по эксплуатации цифрового беспроводного термометра и гигрометра ThermoPro TP60-3 для использования внутри и снаружи помещений.

1. Введение

The ThermoPro TP60-3 is a digital wireless indoor/outdoor thermometer and hygrometer designed to monitor temperature and humidity levels in various environments. This device provides accurate readings for both indoor and outdoor conditions, featuring a long wireless range and the ability to connect with multiple remote sensors. It is suitable for use in homes, baby rooms, nurseries, cellars, basements, warehouses, and greenhouses to ensure optimal environmental control.

Image: The ThermoPro TP60-3 main display unit and three remote wireless sensors, illustrating the complete product package.

2. Что в коробке

• 1 x Основной приемный блок
• 3 x Remote Transmitter Sensors
• 8 батареек типа ААА

3. Продукт закончилсяview

3.1 Main Receiver Unit

The main receiver unit features a large, easy-to-read LCD screen that displays indoor and outdoor temperature and humidity percentages. It also shows temperature and humidity trend indicator arrows, and daily high/low information. The unit is designed for tabletop placement with a built-in stand or can be wall-mounted.

Image: Close-up of the main display unit showing outdoor temperature and humidity, channel indicator, and indoor temperature and humidity with trend arrows.

3.2 Remote Transmitter Sensors

The remote sensors transmit temperature and humidity data wirelessly to the main unit. Each sensor is designed for outdoor use and should be placed in a location protected from direct sunlight and rain. The system supports up to three remote sensors, allowing monitoring of different locations simultaneously.

Image: Diagram showing the main unit receiving data from three remote sensors placed in a bedroom, storage room, and garden, highlighting multi-location monitoring.

4. Настройка

4.1 Установка аккумулятора

1. Open the battery compartment on the back of both the main receiver unit and each remote sensor.
2. Insert the provided AAA Batteries, ensuring correct polarity (+/-).
3. Надежно закройте батарейные отсеки.

4.2 Synchronization Process

After installing batteries, the main unit and remote sensors should automatically synchronize. The RF signal icon on the upper left of the main unit's display will flash during synchronization. If connection is lost or batteries are replaced, follow these steps:

• Ensure batteries are correctly installed in both units.
• Press the TX button on the remote sensor(s) to re-establish connection.

4.3 Рекомендации по размещению

• Основной блок: Place the main unit indoors on a tabletop using its built-in stand or mount it on a wall.
• Дистанционные датчики:
  • Place sensors in an open area, avoiding wall obstructions.
  • Keep sensors away from routers and other electronic devices to prevent high-frequency signal interference.
  • Avoid direct sunlight exposure, as this can lead to inaccurate temperature readings.
  • Always place sensors upright to prevent rain from entering through vent holes.
  • The wireless range is up to 500ft/150m in open areas.

Image: The main unit shown on a tabletop and a remote sensor mounted on an exterior wall, demonstrating flexible placement options.

5. Инструкция по эксплуатации

5.1 Функции дисплея

• Температура и влажность наружного воздуха: Displayed at the top of the screen.
• Индикатор канала: Shows which remote sensor's data is currently displayed (CH1, CH2, CH3).
• Температура и влажность в помещении: Displayed at the bottom of the screen.
• Стрелки тренда: Indicate whether temperature and humidity are rising, falling, or remaining stable.
• МАКС./МИН. записи: Shows the highest and lowest temperature and humidity readings recorded over the last 24 hours or all-time since the last reset.

5.2 Unit Selection (°F/°C)

To switch between Fahrenheit (°F) and Celsius (°C), press the °F/°C button located on the back of the main receiver unit.

5.3 Viewing MAX/MIN записи

Press the MAX/MIN button on the back of the main unit to cycle through the 24-hour and all-time high and low records for temperature and humidity. To clear the records, press and hold the CLEAR button.

5.4 Выбор канала

If using multiple remote sensors, press the CHANNEL button on the back of the main unit to switch between the different sensor channels (CH1, CH2, CH3) and view their respective outdoor readings.

6. Техническое обслуживание

• Уборка: Протирать мягкой тканью, дamp ткань. Не погружать в воду.
• Замена батареи: Замените батарейки, когда на дисплее появится индикатор низкого заряда батареи. Соблюдайте правильную полярность.
• Хранилище: При длительном хранении устройства извлеките батареи, чтобы предотвратить утечку.

7. Поиск Неисправностей

• Нет дисплея/Низкий заряд батареи: Проверьте установку аккумулятора и при необходимости замените.
• Дистанционное считывание показаний датчиков недоступно:
  • Ensure remote sensor is within range (500ft/150m).
  • Press the TX button on the remote sensor to re-sync.
  • Проверьте наличие помех от других электронных устройств.
  • Replace remote sensor batteries.
• Неточные показания:
  • Ensure remote sensor is not in direct sunlight or exposed to rain.
  • Verify proper placement away from heat sources or vents.

8. Технические характеристики

9. Гарантия и поддержка

For warranty information, technical support, or further assistance, please visit the official ThermoPro webПосетите их сайт или свяжитесь со службой поддержки клиентов. Подробную информацию обычно можно найти на упаковке продукта или на сайте производителя. webсайт.

Вы можете посетить Магазин ThermoPro для получения дополнительной информации и информации о продуктах.