Transformers Studio Series Core Starscream Action Figure Instruction Manual

Введение

This manual provides instructions for the assembly, transformation, and care of your Transformers Studio Series Core Starscream action figure. This collectible figure, inspired by the Transformers: Bumblebee movie, converts between robot and jet modes. Please read these instructions carefully to ensure proper use and enjoyment of your figure.

Информация по безопасности

Внимание: Опасность удушья – возможно образование мелких деталей. Не подходит для детей младше 3 лет.

This product contains small components that could pose a choking hazard. Adult supervision is recommended for children aged 8 and up. Keep all packaging materials away from children.

Содержимое упаковки

• 1x Starscream Action Figure (Model F8750)
• 1x Blaster Accessory

Image: The product packaging for the Transformers Studio Series Core Starscream figure, showing the figure in robot mode and the Studio Series branding.

Настраивать

Your Starscream figure comes pre-assembled in robot mode. No additional assembly is required beyond removing it from the packaging. The included blaster accessory can be attached to the figure's hand in robot mode or stored in jet mode.

Image: The Starscream figure in its robot mode, holding the blaster accessory in its right hand, posed dynamically.

Операции: Инструкции по трансформации

The Starscream figure converts between robot mode and jet mode in 14 steps. Follow these instructions carefully to avoid damage to the figure.

Converting from Robot Mode to Jet Mode

1. Remove Blaster: Detach the blaster accessory from the figure's hand. Set it aside for later attachment in jet mode.
2. Position Arms: Rotate the robot's arms downwards and inward, aligning them with the body.
3. Fold Hands: Fold the robot's hands into the forearms if they are not already retracted.
4. Rotate Waist: Carefully rotate the upper body at the waist 180 degrees.
5. Adjust Wings: Fold the wings on the robot's back upwards and slightly inward.
6. Положение ног: Bring the robot's legs together.
7. Fold Feet: Fold the robot's feet upwards to align with the shins.
8. Compress Legs: Compress the lower leg sections into the upper leg sections.
9. Form Jet Nose: The chest section of the robot will form the nosecone of the jet. Extend it forward.
10. Connect Legs to Torso: Securely connect the transformed leg section to the back of the jet mode, ensuring all tabs and slots align.
11. Align Arms: Position the arms along the sides of the jet mode, ensuring they are flush with the main body.
12. Final Wing Adjustment: Adjust the wings to their final position for jet mode, ensuring they are symmetrical.
13. Attach Blaster: The blaster accessory can be attached to a designated port underneath the jet mode, typically near the rear.
14. Verify Transformation: Ensure all parts are securely tabbed and aligned to form a cohesive jet mode.

Image: The Starscream figure fully transformed into its jet mode, viewсверху, показатьasing its sleek design and integrated blaster.

Image: The Starscream figure in jet mode, viewed from the rear, highlighting the thrusters and wing structure.

Converting from Jet Mode to Robot Mode

To convert back to robot mode, reverse the steps above. Pay attention to the alignment of tabs and slots during each step.

1. Remove Blaster: Detach the blaster from the jet mode.
2. Separate Body Sections: Carefully unclip the leg section from the main jet body.
3. Вытяните ноги: Extend the compressed leg sections and unfold the feet.
4. Separate Arms: Unclip and position the arms away from the jet body.
5. Retract Jet Nose: Fold the jet nosecone back into the robot's chest area.
6. Rotate Waist: Rotate the upper body 180 degrees to face forward.
7. Unfold Hands: Extend the robot's hands from the forearms.
8. Position Arms: Bring the arms down to the robot's sides.
9. Adjust Wings: Position the wings on the robot's back as desired for robot mode.
10. Attach Blaster: Place the blaster accessory into either of the robot's hands.
11. Verify Transformation: Ensure all joints are locked and the figure stands stably in robot mode.

Image: The Starscream figure in its robot mode, standing upright, showcasing its detailed design without the blaster.

Обслуживание

• Уборка: Wipe the figure with a soft, dry cloth to remove dust. For stubborn dirt, a slightly damp Можно использовать ткань, которую следует сразу же высушить. Избегайте использования агрессивных химикатов и абразивных чистящих средств.
• Хранилище: Храните фигурку вдали от прямых солнечных лучей и экстремальных температур, чтобы предотвратить изменение цвета или деформацию пластиковых деталей.
• Умение обращаться: Handle the figure by its main body parts. Avoid excessive force on small joints or thin components during transformation to prevent breakage.

Поиск неисправностей

• Сложность трансформации: If a part feels stuck, do not force it. Re-examine the previous steps to ensure correct alignment. Sometimes, a slight adjustment or rotation is needed before a part can move freely.
• Ослабленные суставы: Over time, some joints may become slightly loose. This is normal with repeated use. For minor looseness, a small amount of clear nail polish or a similar friction-enhancing liquid can be applied to the joint and allowed to dry completely.
• Аксессуар: If the blaster accessory does not fit securely, ensure it is oriented correctly and inserted into the designated port.

Технические характеристики

Гарантия и поддержка

For warranty information, product support, or to inquire about replacement parts, please refer to the official Hasbro webПосетите их сайт или свяжитесь напрямую со службой поддержки клиентов. Конкретные условия гарантии могут различаться в зависимости от региона и продавца.

Официальный бренд Webсайт: Transformers Official Store