1. Продукт закончилсяview
The Sovol SH01 Filament Dryer is designed to remove excess moisture from 3D printer filaments, which is crucial for preventing common printing issues such as stringing, bubbling, and poor layer adhesion. This device features real-time monitoring of temperature and humidity, an upgraded fan for even heating, and a sealed design for effective drying and storage. It is compatible with various filament types including PLA, PETG, TPU, and ABS, and supports both 1.75mm and 2.85mm filament diameters.
Image 1.1: The Sovol SH01 Filament Dryer, showcasing its capacity for two filament spools and the digital display.
2. Содержимое упаковки
Пожалуйста, проверьте наличие всех компонентов в упаковке:
- Sovol SH01 Filament Dryer Unit
- Адаптер питания
- Руководство пользователя (этот документ)
Image 2.1: Contents of the Sovol SH01 Filament Dryer package, including the main unit, power adapter, and documentation.
3. Инструкции по настройке
Follow these steps to set up your Sovol SH01 Filament Dryer:
- Размещение: Place the filament dryer on a stable, flat surface.
- Загрузка нити: Open the transparent lid. Place your filament spool(s) inside the dryer. The dryer can accommodate two filament rolls with a width of less than 70mm each, or one filament roll with a width of less than 150mm.
- Filament Outlet: Guide the filament through the designated filament outlet. Ensure the filament is placed counterclockwise for optimal feeding, especially when used as a spool holder during printing.
- Подключение питания: Подключите адаптер питания к сушилке и вставьте его в подходящую розетку.
Image 3.1: Recommended filament port and direction for 3D printers with Bowden Extruder (left) and Direct Drive Extruder (right).
Image 3.2: The SH01 dryer functioning as a filament holder while connected to a 3D printer, supporting drying during printing.
4. Инструкция по эксплуатации
The Sovol SH01 offers precise control over drying parameters:
- Включение питания: Нажимаем кнопку включения (UЧтобы включить устройство, нажмите кнопку. На дисплее отобразятся текущая температура и влажность.
- Установить температуру: Press the 'M' (Mode) button to enter temperature setting mode. Use the 'Up' (^) button to adjust the temperature between 40°C, 45°C, and 50°C. Refer to the table below for recommended temperatures based on filament type.
- Установите время сушки: Press the 'M' button again to enter drying time setting mode. Use the 'Up' (^) button to set the drying duration from 6 hours to 12 hours.
- Начало сушки: Press the 'M' button one more time to confirm settings and enter working mode. The display will show 'WORK' indicating the drying process has begun.
Image 4.1: The control panel of the Sovol SH01, highlighting the On/Off, Function (M), and Up buttons, along with the real-time display of temperature and humidity.
Image 4.2: Guide for adjusting temperature based on filament type, showing recommended ranges for PLA/Wood, PETG/TPU/PVE, and ABS/PC.
Recommended Drying Temperatures:
| Тип нити | Рекомендуемая температура |
|---|---|
| PLA/Wood | 40-50°С |
| PETG/TPU/PVE | 45-50°С |
| АБС/ПК | 50°С |
Power-Off Drying Mode:
The SH01 features excellent sealing performance with silicone and PTFE seals, allowing for long-term filament storage without power. For enhanced drying efficiency and quality in this mode, it is recommended to place up to four bags of desiccants (not included in the package) inside the dryer box.
Image 4.3: The SH01 in power-off mode, illustrating the PTFE seal at the filament outlet, the main silicone seal, and the designated area for desiccant bags to maintain dryness.
5. Техническое обслуживание
To ensure the longevity and optimal performance of your Sovol SH01 Filament Dryer, consider the following maintenance tips:
- Уборка: Periodically wipe the exterior of the dryer with a soft, dry cloth. Avoid using abrasive cleaners or solvents.
- Замена осушителя: If using desiccants, monitor their condition and replace them as needed according to the desiccant manufacturer's instructions.
- Lid Ventilation: During active heating, it is important to open the PTFE seals on the top of the box to allow moisture to evaporate. For very high humidity, occasionally open the main lid for a few hours to vent.
6. Поиск Неисправностей
Ознакомьтесь со следующими распространенными проблемами и их решениями:
- Automatic Shutdown/Not Working: The filament dryer will switch itself off within 3 minutes if 'WORK' is not displayed on the screen. After setting the temperature and drying time, ensure you press the 'M' button again to enter working mode.
- High Humidity Inside the Box: If humidity gets trapped, it is recommended to open the lid several times over a few hours to vent the humidity. Alternatively, you can place 2 small bags of desiccant inside the dryer.
- Шум вентилятора: Fan noise may be caused by interference between the cable in the drying box and the fan blades. Open the drying box to fine-tune the position of the fan. Check if the fan blades are interfered with by circuit lines and comb if any. If the noise persists, contact customer support.
- E0 and E1 Errors: If the screen displays E0 and E1 errors, open the drying box and check all cable sockets on the motherboard for damage or looseness. If problems persist, contact customer support for replacement.
Image 6.1: Visual troubleshooting guide for common issues such as automatic shutdown, high humidity, and fan noise.
Image 6.2: Demonstrates the impact of filament drying on print quality, showing a 'Before' print with strings, bobbles, and extrusion lines, and an 'After' print that is smooth and clean.
7. Технические характеристики
| Особенность | Спецификация |
|---|---|
| Номер модели | SV-SH01-1 |
| Размеры продукта | 9.69 x 6.89 x 9.53 дюйма (246 мм x 175 мм x 242 мм) |
| Вес товара | 3.08 фунта (1.4 кг) |
| Цвет | Белый |
| Compatible Filament Diameters | 1.75мм, 2.85мм |
| Compatible Filament Types | PLA, PETG, TPU, ABS, Wood, PVE, PC |
| Емкость | 2 rolls (width < 70mm) or 1 roll (width < 150mm) |
| Настройки температуры | 40°С, 45°С, 50°С |
| Настройки времени | 6 часа - 12 часов |
| Функции | Real-time Temp/Humidity Display, Built-in Fan, Excellent Seal, Spool Holder Function |
Image 7.1: Detailed dimensions of the Sovol SH01 Filament Dryer and its compatibility with different filament spool sizes.
8. Поддержка и гарантия
For any questions or issues regarding your Sovol SH01 Filament Dryer, please contact Sovol customer support. Our technical support team is available to provide assistance as soon as possible.
Для получения дополнительной информации вы также можете обратиться к официальному руководству пользователя в формате PDF: Sovol SH01 User Manual (PDF)
