Важные инструкции по технике безопасности
Перед установкой или использованием данного обогревателя внимательно ознакомьтесь со всеми инструкциями. Несоблюдение этих инструкций может привести к пожару, поражению электрическим током, серьезным травмам или смерти.
- Электрическое подключение: This heater operates on 240 Volts. All wiring must be performed by a qualified electrician and comply with national and local electrical codes.
- Заземление: Этот обогреватель должен быть заземлен.
- Расположение: Do not install the heater near flammable materials, in areas where gasoline, paint, or other flammable liquids are stored, or where explosive dust is present. Maintain minimum clearances from walls and other objects as specified in the installation section.
- Надзор: Close supervision is necessary when any heater is used by or near children or invalids, and whenever the heater is left operating and unattended.
- Перегрев: To avoid overheating, do not cover the heater. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
- Обслуживание: Disconnect power at the main service panel before performing any maintenance or cleaning.
- Термостат: A separate thermostat is required for operation and is sold separately. Ensure the thermostat is compatible with a fan-forced heater.
Продукт болееview
The Stelpro pulsair RWF0502W is a 240V wall-mounted fan heater designed for supplemental heating in various rooms such as bedrooms, home offices, and living rooms. It utilizes both convection and forced air heating methods to efficiently distribute warmth.
Передний view of the Stelpro pulsair RWF0502W wall fan heater, showing the fan grille and lower air outlet.
Diagram showing the dimensions of the Stelpro pulsair RWF0502W wall fan heater: 17 1/8 inches (435 mm) height, 8 11/16 inches (220 mm) width, and 3 3/16 inches (80 mm) depth.
Установка
Контрольный список перед установкой:
- Убедитесь, что электропитание отключено на главном автоматическом выключателе.
- Убедитесь, что объем поставкиtage matches the heater's rating (240V).
- Confirm you have a compatible wall thermostat (sold separately).
- Gather necessary tools: screwdriver, wire strippers, drill, level, measuring tape.
Варианты монтажа:
The RWF0502W heater can be either surface-mounted directly to the wall or recessed into the wall for a flush finish. Ensure adequate clearance from floors, ceilings, and adjacent walls as per local codes and manufacturer recommendations.
The Stelpro pulsair RWF0502W wall fan heater installed in a modern entryway, positioned below a plant and mirror.
The Stelpro pulsair RWF0502W wall fan heater installed on a blue wall in an entryway, with coats and shoes nearby.
Электрическое подключение:
This heater requires a 240V hardwired connection. Follow the wiring diagram provided and ensure all connections are secure and properly insulated. Connect the heater to a dedicated circuit protected by the appropriate circuit breaker.
Diagram illustrating the 240V hardwired connection for the Stelpro pulsair RWF0502W wall fan heater, showing wires connecting within a junction box.
- Turn off power at the main electrical panel.
- Remove the front grille of the heater to access the wiring compartment.
- Connect the supply wires to the heater's terminals according to the wiring diagram. Ensure proper grounding.
- Secure all connections with wire nuts and ensure no bare wires are exposed.
- Reattach the front grille.
- Install the external wall thermostat according to its manufacturer's instructions.
Операция
The Stelpro pulsair RWF0502W heater is controlled by an external wall thermostat (not included). Once installed and wired correctly, follow these steps:
- Включение питания: Restore power to the heater circuit at the main electrical panel.
- Настройка термостата: Adjust the external thermostat to your desired temperature. The heater will activate when the room temperature falls below the set point.
- Начальная операция: During the first few minutes of operation, the heater may emit a slight odor due to the burning off of manufacturing residues. This is normal and will dissipate quickly.
- Диапазон температур: The heater is designed to operate within a temperature range of 5°C (41°F) to 30°C (86°F).
For optimal performance, avoid placing furniture or other obstructions directly in front of the heater's air outlets.
Обслуживание
Regular maintenance ensures efficient and safe operation of your Stelpro pulsair heater. Always disconnect power at the main circuit breaker before performing any maintenance.
- Уборка:
- Протрите внешнюю поверхность обогревателя мягкой тряпкой.amp Ткань. Не используйте абразивные чистящие средства или растворители.
- Периодически пылесосьте воздухозаборные и воздуховыпускные решетки, чтобы удалить пыль и ворс.
- Инспекция: Annually inspect the heater for any signs of damage, loose connections, or unusual wear. If any issues are found, contact a qualified electrician for repair.
- Без смазки: Двигатель постоянно смазан и не требует дополнительной смазки.
Поиск неисправностей
If your Stelpro pulsair heater is not operating correctly, consult the following table before contacting customer support.
| Проблема | Возможная причина | Решение |
|---|---|---|
| Нагреватель не включается. | На блок не подается питание. Термостат установлен слишком низко. Сработал автоматический выключатель. | Check main electrical panel. Увеличьте настройку термостата. Сбросьте автоматический выключатель. |
| Нагреватель вырабатывает недостаточно тепла. | Размер помещения слишком велик для обогревателя. Airflow obstructed. Проблема с калибровкой термостата. | Ensure heater is appropriately sized for the room. Clear obstructions from grilles. Consult thermostat manual or a qualified electrician. |
| Необычный шум во время работы. | Свободные компоненты. Обломки в вентиляторе. | Disconnect power and inspect for loose parts. Disconnect power and carefully remove any debris. If noise persists, contact support. |
| Отопитель слишком часто включается и выключается. | Thermostat location or setting. Сработала защита от перегрева. | Relocate thermostat away from drafts or direct heat sources. Adjust thermostat differential. Ensure grilles are clear and heater is not covered. Allow unit to cool. |
Технические характеристики
| Особенность | Деталь |
|---|---|
| Бренд | Стелпро |
| Номер модели | RWF0502W |
| Тип крепления | Wall Mount (Surface or Recessed) |
| Тип комнаты | Спальня, домашний офис, гостиная |
| Томtage | 240 Вольт |
| Ampярость | 2.08 Amps |
| Метод нагрева | Convection, Forced Air |
| Настройка минимальной температуры | 5 градусов Цельсия (41°F) |
| Настройка максимальной температуры | 30 градусов Цельсия (86°F) |
| Вес товара | 7 фунта |
| Размеры упаковки | 17.72 x 9.13 x 3.58 дюйма |
| СКП | 626296002285 |
Гарантия
Stelpro products are manufactured to high standards and are covered by a limited warranty. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official Stelpro webСохраните чек о покупке для предъявления гарантийных претензий.
Поддержка клиентов
For technical assistance, replacement parts, or further inquiries, please contact Stelpro customer service. Contact information can typically be found on the product packaging, the official Stelpro website, or by referring to the documentation included with your purchase.
Note: Always provide your product model number (RWF0502W) when contacting support.
