Руководство пользователя системы дистанционного управления камином и термостата SkyTech SKY-TS-R-2-A

Введение

The SkyTech TS/R-2-A remote control system is designed to provide safe and reliable operation for gas heating appliances. This system allows for both thermostatic and manual control from the transmitter. It operates using radio frequencies (RF) within a 20-foot range, utilizing non-directional signals and one of 1,048,576 security codes for secure communication. The remote receiver, powered by four AA batteries, processes commands from the transmitter to manage the appliance's operation.

This manual provides detailed instructions for the installation, operation, and maintenance of your SkyTech TS/R-2-A system.

Компоненты системы

The SkyTech TS/R-2-A system includes the following components:

• Передатчик: The handheld or wall-mounted unit with an LCD screen and control buttons.
• Получатель: The unit that connects to the gas appliance and receives signals from the transmitter.
• Wall Clip: For mounting the transmitter.
• Настенная пластина: For mounting the receiver in a wall.
• Wires with Connectors: For connecting the receiver to the gas appliance.
• Аккумуляторы: Required for both transmitter and receiver.
• Инструкция по эксплуатации: Этот документ.

Изображение: Оверview of the SkyTech TS/R-2-A system components, including the receiver, transmitter, and wall plate.

Настройка и установка

1. Установка аккумулятора

Передатчик: Insert the specified batteries into the transmitter. Ensure correct polarity. The LCD screen should activate. (Typically uses AAA or similar small batteries, not explicitly detailed in product data).

Получатель: Insert four AA batteries into the receiver. The receiver is designed for millivolt gas valves only and acts as a dry contact switch, meaning it will not output any voltage.

2. Размещение приемника

The receiver can be installed in several locations:

• Behind the included faceplate in a wall.
• On the hearth.
• Under the fireplace, behind the control access panel.

Ensure the receiver is placed within 20 feet of the intended transmitter location for optimal signal reception.

3. Подключение приемника

Connect the receiver to your gas heating appliance using the provided wires with connectors. Refer to your appliance's manual for specific wiring instructions for a remote control system. The receiver acts as a simple on/off switch for the millivolt gas valve.

4. Pairing (Learning Function)

Для установления связи между передатчиком и приемником:

1. Locate the "LEARN" button on the receiver.
2. Press and hold the "LEARN" button on the receiver until you hear a beep or see an indicator light flash (refer to receiver specific indicators).
3. Within 10 seconds, press any button on the transmitter (e.g., "ON" or "SET").
4. The receiver should emit a confirmation sound or light, indicating successful pairing.

Note: If pairing fails, ensure both units have fresh batteries and are within range, then repeat the process.

Инструкция по эксплуатации

Receiver Mode Selection

The receiver has a 3-position slide switch for selecting the mode of operation:

• НА: The gas appliance will remain continuously on, bypassing remote control.
• УДАЛЕННЫЙ: The gas appliance will operate according to commands from the transmitter.
• OFF: The gas appliance will remain continuously off, bypassing remote control.

Set the receiver switch to УДАЛЕННЫЙ for normal operation with the transmitter.

Функции передатчика

The transmitter features an LCD screen and three buttons: ON, НАБОР, и ВЫКЛЮЧЕННЫЙ, along with up/down arrows.

• ЖК-дисплей: Shows the current room temperature and the set temperature (in Fahrenheit or Celsius).
• Кнопка включения: Manually turns the gas appliance on.
• Кнопка ВЫКЛ: Manually turns the gas appliance off.
• Кнопка SET: Used to enter thermostatic mode and adjust the desired temperature.
• Стрелки вверх/вниз: Used to adjust the set temperature in thermostatic mode.

Ручное управление

To manually control the appliance:

• Нажмите ON кнопку, чтобы включить прибор.
• Нажмите ВЫКЛЮЧЕННЫЙ кнопку, чтобы выключить прибор.

Thermostatic Operation

To operate the appliance thermostatically:

1. Ensure the receiver switch is set to УДАЛЕННЫЙ.
2. Нажмите НАБОР button on the transmitter. The set temperature will flash on the LCD.
3. Используйте Up or Вниз Кнопки со стрелками для регулировки желаемой температуры.
4. Нажимать НАБОР again or wait a few seconds for the setting to be saved.

The appliance will now cycle on and off to maintain the set temperature. Typically, the system activates when the room temperature drops a few degrees below the set temperature and turns off when it reaches a few degrees above the set temperature.

Изменение единиц измерения температуры (°F/°C)

The LCD screen displays temperature in Fahrenheit (°F) or Celsius (°C). Consult the transmitter's specific instructions (often a small switch or button combination) to toggle between these units if needed.

Обслуживание

Замена батареи

Replace batteries in both the transmitter and receiver annually, or immediately if the display becomes dim, the range decreases, or the system becomes unresponsive. Low batteries can lead to communication issues and unexpected system behavior.

• Передатчик: Typically uses AAA or similar small batteries. Refer to the battery compartment for exact type.
• Получатель: Uses 4 AA batteries.

Always use fresh, high-quality alkaline batteries. Dispose of old batteries responsibly.

Уборка

Wipe the transmitter and receiver with a soft, dry cloth. Do not use abrasive cleaners or immerse the units in water.

Поиск неисправностей

• Система не отвечает:
  • Check batteries in both transmitter and receiver. Replace if low.
  • Ensure the receiver's slide switch is set to УДАЛЕННЫЙ.
  • Verify the transmitter and receiver are within the 20-foot operating range.
  • Re-attempt the pairing (learning) process.
• Appliance Does Not Turn On/Off in Thermostatic Mode:
  • Confirm the set temperature is appropriate for the desired operation (e.g., set higher than room temp to turn on).
  • Check for significant temperature fluctuations or drafts near the transmitter that might affect readings.
  • Ensure the receiver is properly wired to the gas appliance.
• Неточные показания температуры:
  • Ensure the transmitter is not placed near heat sources, direct sunlight, or drafts that could skew readings.
  • Compare the transmitter's reading with another reliable thermometer in the same location. Small discrepancies (1-3 degrees) can occur due to placement or sensor variations.
• Прерывистая работа:
  • This can often be caused by low batteries. Replace them.
  • Check for sources of radio frequency interference (e.g., other wireless devices, large metal objects) between the transmitter and receiver.

Технические характеристики

Гарантия и поддержка

Specific warranty information for the SkyTech TS/R-2-A system is not provided in this manual. For details regarding warranty coverage, please refer to the documentation included with your purchase or contact SkyTech customer support directly.

For technical assistance or further inquiries, please visit the official SkyTech webили обратитесь в службу поддержки клиентов. Контактная информация обычно указана на упаковке продукта или на сайте производителя. webсайт.