D149H181 Ed.08
АКО-Д14918
The АКО-Д14918 programming key allows you to quickly and easily copy configured settings from one controller to another with the same functionality
Предупреждения
-Using the equipment without following the manufacturer’s instructions may affect the device’s safety requirements.
-The unit must be used in a location protected from vibrations, water and corrosive gases, where the ambient temperature does not exceed that shown in the technical data.
-Connecting this key to unsupported devices (see table) can cause serious damage to both pieces of equipment.
-In equipment with active communication, log out of communications software or disconnect the cable before connecting the programming key. The communication controller’s address must be 1.
Описание
- СИД COM
- ЗАПИСАТЬ КЛЮЧ
- EXTERNAL POWER CONNECTOR
- READ KEY
- Светодиод горит
- СОЕДИНИТЕЛЬНЫЙ КАБЕЛЬ
Совместимость
Refer to the instruction manual of your equipment on its compatibility with the АКО-Д14918 ключ программирования.
Connecting incompatible devices can permanently damage the key.
Проводка
- ВАЖНЫЙ: Pay attention to the orientation of the connector.
- АКО-80018
(Необязательный) - АКО-Д14918
Источник питания
-If the controller is in operation (on-site programming), the key does not require an external power supply (it is powered via the connecting cable).
-If the controller is NOT powered (workshop programming), the key requires a 12Vdc/500 mA external power supply (АКО-80018 или эквивалентное).
Операция
ВАЖНЫЙ: After connecting the key to the equipment wait for 5 seconds before starting the reading or writing process.
RECORD key
Write the data contained in the key memory to the controller.
Keep the key pressed until the КОМ led starts flashing quickly.
When recording is complete the controller will reset.
READ key
It reads the data from the controller and stores them in the programming key.
Keep the key pressed until the КОМ led starts flashing quickly.
When recording is complete the controller will reset.
Светодиод горит
Steady or flashing: Indicates that the key is connected to the controller.
СИД COM
Устойчивый: Indicates an error in the transmission/reception of data
Быстро мигает: Indicates transmission/reception of data in progress. At the end of the transmission СИД COM выключится.
Медленное мигание: Indicates compatibility error- the data contained in the memory of the key is not compatible with the model of controller connected. Data can only be read from the controller to the key.
ПРИМЕЧАНИЕ: To restart after a transmission or compatibility error, turn off the power supply or disconnect the controller connector cable.
ВАЖНЫЙ: Никогда disconnect the programming key during data transmission.
Технические характеристики
Length of cable from programming key to controller . . . . . . . . . . . . . 300 mm
Объем поставкиtage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Vdc nominal
Supply current . . . . . . . . . . . . . . . . . . . . . . . . . . . . AKO-80018 / 500 mA máx.
Экологические характеристики:
Ambient working temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . 0ºC to 50ºC
Storage temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -30ºC to 70ºC
АКО ЭЛЕКТРОМЕХАНИКА, SA
Av. Roquetes, 30-38 | 08812 Sant Pere de Ribes | Barcelona | España
35D149181 REV.07 2025
Мы оставляем за собой право поставлять материалы, которые могут незначительно отличаться от описанных в наших технических описаниях.
Обновленная информация доступна на нашем webсайт.
Документы/Ресурсы
 |
AKO D14918 Programming Key [pdf] Руководство по эксплуатации AKO-D14918, AKO-80018, D14918 Programming Key, Programming Key, Key |