1. Введение
This manual provides essential instructions for the proper installation, operation, and maintenance of your original replacement water tank accessory. This water tank is designed for use with Lydsto R1 Edge, TP-Link Tapo RV30 Plus, and TP-Link Tapo RV20 Max robotic vacuum cleaners, ensuring optimal mopping performance.
2. Продукт закончилсяview
The water tank accessory is a crucial component for your robotic vacuum cleaner's mopping function. It holds water and dispenses it to the mopping pad, allowing for effective wet cleaning. The tank includes a filter compartment to prevent debris from entering the water dispensing system.
Рисунок 2.1: Главное view of the water tank accessory with filter installed.
Рисунок 2.2: Сверху вниз view of the water tank, showing the filter compartment and water inlet.
Рисунок 2.3: Вверху view of the water tank with the filter compartment open, showing a white filter.
3. Технические характеристики
| Особенность | Деталь |
|---|---|
| Название бренда | Лидсто |
| Номер модели | Lydsto R1 Edge (Compatible with TP-Link Tapo RV30 Plus/RV20 Max) |
| Тип | Части пылесоса |
| Материал | Пластик |
| Высокоопасный химический | Никто |
| Источник | Материковый Китай |
4. Настройка и установка
- Демонтаж старого водонагревательного бака (если имеется): Turn off your robotic vacuum cleaner and place it upside down or on its side. Locate the existing water tank and carefully remove it according to your vacuum cleaner's main instruction manual.
- Открытый отсек для фильтра: Locate the filter compartment on the new water tank. Gently open the latch or cover to access the filter.
- Установить фильтр: Ensure the filter is correctly seated within its compartment. If replacing an old filter, insert the new one firmly.
- Заполните резервуар для воды: Locate the water inlet on the tank. Open the rubber stopper or cap and carefully fill the tank with clean tap water. Do not overfill. Close the stopper/cap securely to prevent leaks.
- Insert New Water Tank: Align the new water tank with the corresponding slot on your robotic vacuum cleaner. Gently push it into place until you hear a click or feel it securely seated. Ensure there are no gaps.
Figure 4.1: Filter compartment open, filter removed.
Figure 4.2: Filter removed and placed next to the tank for illustration.
5. Инструкция по эксплуатации
Once the water tank is installed and filled, your robotic vacuum cleaner is ready for mopping. Refer to your vacuum cleaner's main user manual for specific instructions on activating the mopping mode, adjusting water flow, and scheduling cleaning tasks. Ensure the mopping pad is attached correctly before starting a mopping cycle.
6. Техническое обслуживание
Regular maintenance of the water tank ensures optimal performance and extends the lifespan of your accessory.
- Empty and Clean After Each Use: After each mopping cycle, remove the water tank from the vacuum cleaner. Empty any remaining water. Rinse the tank thoroughly with clean water to prevent mold or mildew buildup. Allow it to air dry completely before re-installing or storing.
- Очистка/замена фильтра: Periodically check the filter inside the water tank. If it appears dirty or clogged, rinse it under running water. If the filter is heavily soiled or damaged, replace it with a new one. The frequency of replacement depends on usage.
- Избегайте едких химикатов: Do not use detergents, bleach, or other harsh cleaning chemicals in the water tank, as these can damage the tank material or the vacuum cleaner's internal components. Use only clean water or manufacturer-approved cleaning solutions if specified by your vacuum cleaner's manual.
Рисунок 6.1: Example of a filter inside the compartment.
7. Поиск Неисправностей
- Вода не подается:
- Ensure the water tank is properly filled and securely installed.
- Check if the filter is clogged and clean or replace it if necessary.
- Verify that the mopping mode is activated on your vacuum cleaner.
- Утечка воды:
- Ensure the water inlet stopper/cap is securely closed.
- Check for any cracks or damage to the water tank. If damaged, replacement is necessary.
- Confirm the tank is correctly seated in the vacuum cleaner.
- Tank Does Not Fit:
- Double-check the compatibility of the water tank with your specific vacuum cleaner model (Lydsto R1 Edge, TP-Link Tapo RV30 Plus, or RV20 Max).
- Ensure no obstructions are preventing the tank from seating correctly.
8. Советы пользователю
- Проверка совместимости: Always confirm that the water tank is compatible with your specific robot vacuum model (e.g., Lydsto R1 Edge, TP-Link Tapo RV30 Plus, RV20 Max) before installation to ensure a perfect fit and function.
- Используйте дистиллированную воду: To prevent mineral buildup and prolong the life of your water tank and vacuum's internal components, consider using distilled or filtered water, especially in areas with hard water.
- Регулярные проверки фильтров: Even if water seems to be dispensing, a partially clogged filter can reduce efficiency. Make it a habit to check and rinse the filter regularly.
9. Гарантия и поддержка
For any issues not covered in this manual, or for warranty inquiries, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase. Specific warranty terms may vary by region and seller.
