Инструкция по эксплуатации приемника Jumper ELRS Aion Receiver Series

Введение

Спасибо за покупкуasing a Jumper Aion ELRS full duplex telemetry receiver. This manual provides detailed instructions for the Jumper ELRS Aion RX NANO, R1 V2 Mini, ELRS RX MINI, and ELRS RX MINI-SE 2.4GHz 16-channel receivers. To fully enjoy the benefits of your system, please read these instructions carefully and set up the device as described below.

The ELRS RX NANO version includes a Power Amplifier (PA) for the longest control distance. The MINI and MINI-SE versions feature different antennas, with the ELRS RX MINI-SE having a weaker antenna performance and a comparatively shorter range.

Технические характеристики

Below are the detailed specifications for each receiver model:

R1 V2 Mini Receiver

• Размер: 17.2 x 8.8 x 4.5 мм (длина x ширина x высота)
• Масса: 1.5 г
• Каналы: 16Ch
• Рабочий объемtage: 3.5В-6В
• Рабочий ток: 60mA @ 5V
• Режим работы: Полный ассортимент
• Расстояние управления: >2KM
• Совместимость: D16 Mode Transmitter

ELRS RX MINI Receiver

• Измерение: 17.2 x 8.8 x 4.3 мм (ДхШхВ)
• Масса: 1.1 г
• Количество каналов: 16Ch
• Рабочий объемtage Диапазон: 3.5В-6В
• Рабочий ток: 60mA @ 5V
• Рабочий диапазон: Полный ассортимент
• Расстояние: >5KM
• Совместимость: Radios in ELRS 2.4 mode

ELRS RX NANO Receiver

• Размеры: 17.5 x 9.8 x 4.3 мм (длина x ширина x высота)
• Масса: 1.2 грамм
• Каналы: 16Ch
• Рабочий объемtage: 3.5-6В
• Рабочий ток: 60mA @ 5V
• Режим работы: Полный ассортимент
• Расстояние управления: >8KM
• Совместимость: ELRS 2.4

ELRS RX MINI-SE Receiver

• Размер: 12.8 х 9.8 х 3.6 мм
• Масса: 0.8 г
• Каналы: 16ч
• Рабочий объемtage: 3.5-6В
• Рабочий ток: 60mA @ 5V
• Режим работы: Полный ассортимент
• Расстояние управления: >5 KM
• Совместимость: ELRS 2.4

Настраивать

Процедура обязательного исполнения

Binding is the process of uniquely associating a receiver with a transmitter or transmitter RF module. A transmitter's internal or external RF module can be bound to multiple receivers (though not to be used simultaneously). Each receiver can only be bound to one RF module. Follow these steps to complete the binding procedure:

1. Put your transmitter or transmitter RF module into binding mode.
2. Power on the receiver three times. The green LED light will flash twice, indicating the receiver is in binding mode.
3. Initiate the binding process on your radio. Once successfully bound, the receiver's green LED light will remain solid.

Примечание: If the receiver is not bound within 20 seconds after power-on, it will enter Wi-Fi firmware updating mode, and the green LED light will flash continuously.

Проводка черезview

Refer to the diagrams below for the pinout and physical layout of the receivers. These diagrams illustrate the connections for GND (Ground), VCC (Power), TX (Transmit), RX (Receive), LED indicator, and BOOT0 pin.

Операционная

Failsafe Configuration

Failsafe is a critical safety feature that defines the receiver's output behavior when the control signal from the transmitter is lost. This ensures that your RC model reacts predictably in case of signal interruption, reducing the risk of damage or loss.

For receivers supporting ELRS RF mode, Failsafe settings can be configured via the radio interface. This typically includes options for 'No Pulse', 'Hold', and 'Custom' modes for each channel. To access these settings, navigate to: MODEL SETUP/internal RF/Failsafe на вашем передатчике.

Важное примечание: Failsafe settings configured via the transmitter for channel output position are specifically for ELRS RF mode. Transmitter-based Failsafe settings take precedence over any receiver-side settings. Always ensure a reasonable Failsafe configuration to minimize the risk of crashes and damage.

Обслуживание

To ensure the longevity and optimal performance of your Jumper ELRS Aion receiver, consider the following maintenance guidelines:

• Содержать в чистоте: Regularly inspect the receiver for dust, dirt, or debris. Use a soft, dry brush or compressed air to gently clean the components.
• Защищать от влаги: Avoid exposing the receiver to moisture or extreme humidity. If used in damp conditions, ensure it is properly protected.
• Физическая защита: Mount the receiver securely within your RC model to prevent vibrations and physical damage during operation.
• Уход за антенной: Ensure the antenna is not bent sharply or damaged. A damaged antenna can significantly reduce range and signal quality.
• Обновления прошивки: Periodically check the official Jumper website for any available firmware updates. Keeping your receiver's firmware up-to-date can improve performance and add new features.

Поиск неисправностей

If you encounter issues with your Jumper ELRS Aion receiver, consider the following troubleshooting steps:

• Ошибка связывания: If the receiver does not bind, ensure your transmitter is in binding mode and that you are following the correct power-on sequence for the receiver (power cycling three times). Verify that both the transmitter and receiver are operating on the same ELRS 2.4GHz protocol.
• No Control/Signal Loss: Check all wiring connections (GND, VCC, TX, RX) to ensure they are secure and correctly connected. Verify that the antenna is properly attached and undamaged. Ensure your transmitter is powered on and within range.
• Unexpected Model Behavior: Review your Failsafe settings on the transmitter. Incorrect Failsafe configuration can lead to unpredictable behavior upon signal loss.
• Receiver Enters Wi-Fi Mode: If the green LED flashes continuously after power-on, the receiver has entered Wi-Fi firmware update mode. This typically happens if binding is not completed within 20 seconds. Power cycle the receiver and attempt binding again.
• Уменьшенный диапазон: Check for obstructions between the transmitter and receiver. Ensure the receiver's antenna is positioned optimally and away from carbon fiber or metal parts that can shield the signal.

Советы пользователей

• Совместимость передатчика: These ELRS receivers are compatible with Jumper T-Pro and Jumper T-Lite transmitters that support the ELRS protocol. Ensure your transmitter is running an ELRS version for proper functionality.
• Размещение антенны: For optimal range and signal integrity, ensure the receiver antenna is positioned clear of other electronics, carbon fiber frames, and metal components on your RC model.
• Firmware Matching: For best performance and compatibility, it is recommended to keep the firmware version of your ELRS receiver and transmitter module synchronized.

Гарантия и поддержка

Jumper products are designed for reliability and performance. For specific warranty information, please refer to the terms and conditions provided at the time of purchase or contact your retailer. For technical support, firmware updates, and additional resources, please visit the official Jumper webсайт или свяжитесь с их службой поддержки.