Введение
The Zooz ZEN58 800LR is a compact Z-Wave Long Range Low Voltage XS Relay designed to integrate low-voltage devices into your Z-Wave smart home system. It enables ON/OFF control for loads up to 3 Amps and supports 0-240 Volts, making it suitable for applications such as garage doors, entry gates, or controlling humidifiers. This manual provides detailed instructions for safe installation, operation, and maintenance of your ZEN58 800LR relay.
Информация по безопасности
Please read all safety precautions before installation and operation. Failure to follow these instructions may result in electric shock, fire, or property damage.
- Данное устройство предназначено только для использования внутри помещений.
- Перед установкой или обслуживанием убедитесь, что питание отключено на автоматическом выключателе.
- Installation should be performed by a qualified electrician or trained professional.
- Не превышайте максимальную нагрузку 3 Ampс при 240В.
- The device is powered by 9-40 V AC/DC only.
- Use dry contact input (NO Voltage) for connected switches or sensors.
- Maximum wire size for terminals is 14 AWG.
- Do not use with dimmers or electronic switches; only simple toggle and momentary switches are supported for analog input.
Продукт болееview
Что в коробке?
- Zooz ZEN58 800LR Smart Relay
- Руководство пользователя
Основные характеристики
- Z-Wave контроль: Adds Z-Wave ON/OFF functionality to low-voltage loads up to 3 Amps, 0-240 Volts.
- Аналоговый вход: Connects to a wall switch (toggle or momentary) or binary sensors (e.g., open/close, water/no water) with no voltage on input wires.
- Компактный дизайн: Extra small size (1.2" tall, 1.0" wide, 0.6" deep) for installation in crowded or shallow electrical boxes.
- Расширенная безопасность: Features S2 authenticated security protocol and SmartStart for secure and easy pairing.
- Большой диапазон: Z-Wave Long Range enabled for extended communication.
- Широкая совместимость: Works with various Z-Wave hubs including Z-Box Hub, Hubitat, Home Assistant (Z-Wave JS), and SmartThings (for basic on/off).
Настройка и установка
Инструкции по электропроводке
Before proceeding, ensure power is OFF at the circuit breaker. The ZEN58 800LR requires a 9-40V AC/DC power source and uses dry contact inputs. Do not apply voltage to the input (IN) terminals.
- Подключение питания: Connect your 9-40V AC/DC power supply to the DC+ and DC- terminals on the relay. Observe polarity if using DC.
- Подключение нагрузки: Connect the load you wish to control (e.g., garage door opener, solenoid valve) to the OUT terminals. This is a dry contact output, meaning it acts as a switch to complete or break a circuit for your load.
- Analog Input (Optional): If connecting a wall switch or binary sensor, connect it to the IN and S terminals. Ensure the switch provides a dry contact closure (no voltage). This input supports simple toggle or momentary switches.
- Безопасная проводка: Ensure all wire connections are secure and within the maximum 14 AWG wire size.
Передний view of the ZEN58 800LR relay, illustrating the terminal block for power input (DC+, DC-), dry contact output (OUT), and dry contact analog input (IN, S).
Назад view of the ZEN58 800LR relay, displaying regulatory information, Z-Wave region, firmware version, and the SmartStart DSK (Device Specific Key) for secure pairing.
Size comparison of the ZEN58 800LR relay, highlighting its compact dimensions (1.0" wide, 1.2" tall) relative to a US quarter and another Zooz relay model, demonstrating its suitability for tight spaces.
Z-Wave сопряжение
The ZEN58 800LR supports S2 authenticated security and SmartStart for easy and secure inclusion into your Z-Wave network. A compatible Z-Wave hub is required (sold separately).
- Включение питания: After wiring, restore power to the circuit. The relay will power on.
- Включение SmartStart: If your Z-Wave hub supports SmartStart, scan the QR code on the back of the relay (or on the packaging) using your hub's app. The device will automatically include into your network.
- Ручное включение: If your hub does not support SmartStart, initiate "Add Device" or "Z-Wave Inclusion" mode on your Z-Wave hub. Then, quickly press the Z-Wave button on the ZEN58 800LR three times. The LED indicator will confirm successful pairing.
- S2 Безопасность: During inclusion, your hub may prompt you to enter the 5-digit Device Specific Key (DSK) found on the QR code label for S2 authenticated security.
Compatible Z-Wave Hubs:
- Z-Box Hub (fully compatible)
- Хабитат
- Home Assistant (Z-Wave JS)
- HomeSeer
- SmartThings (for basic on/off functionality)
Инструкция по эксплуатации
Once successfully paired with your Z-Wave hub, the ZEN58 800LR can be controlled remotely via your Z-Wave network or locally via the connected analog input.
- Z-Wave контроль: Use your Z-Wave hub's interface or associated smart home app to turn the connected load ON or OFF. The relay will respond to commands sent over the Z-Wave network.
- Analog Input Control: If a physical switch is connected to the IN and S terminals, operating this switch will toggle the state of the relay. For example, pressing a momentary switch connected to a garage door opener will activate the opener.
- Индикация состояния: The LED indicator on the relay provides visual feedback on its status (e.g., pairing mode, ON/OFF state). Refer to your hub's documentation for specific LED behavior during pairing.
Обслуживание
The Zooz ZEN58 800LR is designed for reliable, long-term operation with minimal maintenance.
- Следите за тем, чтобы устройство не было запылено и влажным.
- Не пытайтесь самостоятельно вскрывать или ремонтировать устройство. Для любых сервисных работ обращайтесь к квалифицированному персоналу.
- Периодически проверяйте соединения проводов, чтобы убедиться в их надежности.
Поиск неисправностей
Распространенные проблемы и решения
- Устройство не подключается:
- Ensure the device is powered correctly (9-40V AC/DC).
- Убедитесь, что ваш Z-Wave-хаб находится в режиме включения.
- Try pressing the Z-Wave button on the relay 3 times quickly.
- Move the relay closer to the hub during the pairing process.
- Perform a Z-Wave exclusion first (see your hub's manual) and then try inclusion again.
- Relay not responding to commands:
- Проверьте питание реле.
- Verify the Z-Wave network connection and signal strength.
- Ensure the connected load is within the 3 Amp предел.
- Check the wiring to the load.
- Analog input switch not working:
- Confirm the switch is a dry contact type (no voltagе выход).
- Ensure the switch is properly connected to the IN and S terminals.
- Verify the switch type is toggle or momentary, not a dimmer or electronic switch.
- Poor Z-Wave Long Range performance:
- Ensure your Z-Wave hub supports Z-Wave Long Range.
- Minimize physical obstructions (concrete walls, large metal objects) between the relay and the hub.
- Consider adding Z-Wave repeaters if range is consistently an issue.
Технические характеристики
| Номер модели | ЗЕН58 800LR |
| Z-Wave регион | США/Канада/Мексика |
| Власть | 9-40 В переменного/постоянного тока |
| Максимальная нагрузка | 3 Ampс на 240В |
| Максимальный размер провода | 14 AWG |
| Z-Wave Диапазон | Up to 300 feet line of sight (1300 feet with Z-Wave Long Range enabled) |
| Размеры (Д x Ш x В) | 1.2 x 1.0 x 0.6 дюйма (30.5 x 25.4 x 15.2 мм) |
| Рабочая температура | 32–104° F (0–40° C) |
| Установка и использование | Только в помещении |
| Протокол подключения | Z-волна |
| Безопасность | S2 Аутентифицировано |
| Сертификация | ФКС |
| GTIN/UPC | 853478006582 |
Гарантия и поддержка
The Zooz ZEN58 800LR comes with a standard warranty. You can extend this to a Гарантия 5 год by registering your device within 30 days of purchase. Zooz also provides пожизненная техническая поддержка за свою продукцию.
For warranty registration, technical assistance, or further inquiries, please visit the official Zooz webсайт или обратитесь в службу поддержки клиентов.
