Введение
This manual provides detailed instructions for the safe and efficient use of your Wefomey 65.6ft COB LED Strip Light. Please read this manual thoroughly before installation and operation to ensure proper functionality and safety.
Содержимое упаковки
- 65.6ft warm white COB LED strip (2 rolls of 32.8ft)
- Пульт дистанционного управления RF
- Контроллер
- UL Listed DC 24V 48W power supply
- 2-pin 8mm COB LED connectors
- 2-pin 8mm COB LED connector extension wire
- Монтажные кронштейны
Важные инструкции по технике безопасности
- Перед установкой или обслуживанием убедитесь, что источник питания отключен.
- Данный продукт предназначен только для использования внутри помещений.
- Do not expose the LED strip to water or high humidity.
- Используйте только прилагаемый адаптер питания.
- Do not bend the LED strip sharply or apply excessive force.
- Хранить в недоступном для детей месте.
Настройка и установка
Шаг 1: Подготовка поверхности для установки
Ensure the surface is clean, dry, and smooth for optimal adhesive performance. Remove any dust, grease, or moisture.
Step 2: Connect the Components
Connect the COB LED strip to the controller, and then connect the controller to the DC 24V 48W power supply. Finally, plug the power supply into a standard electrical outlet.
Image: Illustration of how to connect the LED strip to the controller and power supply. The strip is flexible and can be used for various DIY lighting projects.
Step 3: Mount the LED Strip
Peel off the backing from the adhesive tape on the back of the LED strip and firmly press the strip onto the desired surface. For added security, use the included mounting brackets and screws.
Step 4: Cutting and Reconnecting (Optional)
The LED strip can be cut at designated marks (every 50mm / 1.97 inches) to achieve the desired length. The middle of the metal point on the strip light indicates a cutting mark.
To reconnect cut sections, use the provided 2-pin 8mm COB LED connectors. Ensure correct polarity (positive to positive, negative to negative) when making connections.
Image: Detailed instructions on how to use 2-pin 8mm COB LED strip connectors, including opening the cap, inserting the strip, checking orientation, and closing the clip. Examples of L-shaped and T-shaped connections are shown.
Инструкция по эксплуатации
Включение/выключение питания
Use the ON/OFF button on the RF remote control or the inline controller to turn the lights on or off.
Яркость затемнения
The LED strip offers dimmable brightness with 6 levels (10%, 25%, 40%, 60%, 80%, 100%). Use the brightness increase/decrease buttons on the remote or the fixed brightness level buttons (10%, 25%, 50%, 100%).
Image: A remote control is shown adjusting the brightness of the LED strip light, illustrating the 10% to 100% dimming capability in a room with a fireplace.
Режимы освещения
The remote control provides 3 dynamic lighting modes: Jump, Gradient, and Flicker. Select these modes using the dedicated buttons on the remote.
Функция таймера
Set the LED strip to automatically turn off after 10, 30, or 60 minutes using the timer buttons on the RF remote.
Image: A bedroom scene showing the LED strip light installed behind a headboard, with a remote control indicating timer settings for 10, 30, and 60 minutes.
Функция памяти
The controller has a memory function that restores the LED strip to its last used setting when powered on.
Сопряжение с пультом дистанционного управления
To pair the remote control (1 to 1 pairing) or cancel pairing: After powering on, press and hold the "Sun" button and the "Moon" button simultaneously for 1-3 seconds until the strip light flashes.
Image: An RF remote control highlighting the "Sun" and "Moon" buttons for pairing, with an example of LED strip lights illuminating the exterior of a house.
Обслуживание
- Regularly wipe the LED strip with a soft, dry cloth to remove dust.
- Не используйте абразивные чистящие средства или растворители.
- Убедитесь, что все соединения надежны.
Поиск неисправностей
| Проблема | Возможная причина | Решение |
|---|---|---|
| Свет не включается. | Power supply disconnected, faulty connection, or remote battery low. | Check all power connections. Ensure the power adapter is plugged in. Replace remote battery if necessary. |
| Свет неожиданно мерцает или приглушается. | Loose connection, insufficient power, or faulty strip section. | Check all connections for tightness. Ensure the power supply wattage is adequate for the total strip length. |
| Пульт дистанционного управления не отвечает. | Remote battery low, remote not paired, or obstruction. | Replace remote battery. Re-pair the remote control (refer to "Remote Control Pairing" section). Ensure no obstructions between remote and controller. |
| Клей не держит. | Surface not clean or smooth, or strip too heavy for adhesive. | Clean the surface thoroughly before application. Use additional mounting brackets or clips for better support. |
Технические характеристики
| Особенность | Деталь |
|---|---|
| Номер модели | WF-WWCOB-20M |
| Бренд | Уэфоми |
| Светлый цвет | 3000К теплый белый |
| Длина | 65.6 футов (2 рулона по 32.8 футов) |
| Томtage | 24 В постоянного тока |
| Ватtage | 48 Вт |
| Тип источника света | COB-светодиод |
| CRI | >90 |
| Диммируемый | Да |
| Метод контроля | Радиочастотный пульт дистанционного управления |
| Использование внутри и снаружи помещений | В помещении |
| Режущий блок | 50 мм (1.97 дюймов) |
| Ширина полосы | 8 мм (0.32 дюймов) |
Image: A table summarizing key specifications such as CRI (>90), CCT (3000K), Length (65.6ft/20m), Cutting Size (1.97in/50mm), Power Rated (48W), LEDs Quantity (6480), Width (0.31in/8mm), and Waterproof (IP22).
Гарантия и поддержка
Информация о гарантии
This Wefomey COB LED Strip Light comes with a 2-year manufacturer's warranty.
Поддержка клиентов
For technical assistance, troubleshooting, or warranty claims, please contact Wefomey customer support. Refer to the product packaging or the seller's information for contact details.