1. Введение
This manual provides detailed instructions for the installation, operation, and maintenance of your SENSTREE Dual Probe Temperature & Humidity Controller, Model THT1032-ZJ. This device is designed to precisely monitor and control both temperature and humidity in various environments, utilizing independent sensors for optimal performance. Please read this manual thoroughly before use to ensure safe and efficient operation.
2. Информация по технике безопасности
Соблюдайте следующие меры предосторожности, чтобы предотвратить травмы или повреждение устройства:
- Убедитесь, что источник питания vol.tage matches the device's specifications (240 Volts AC).
- Do not immerse the controller unit in water or expose it to excessive moisture. The probes are water-resistant, but the main unit is not.
- Avoid exceeding the maximum rated current of 10 Amps per outlet. Overloading can cause damage or fire.
- Храните устройство в недоступном для детей месте.
- Не пытайтесь разбирать или ремонтировать устройство самостоятельно. Обратитесь к квалифицированному специалисту для обслуживания.
- Обеспечьте надлежащую вентиляцию вокруг контроллера, чтобы предотвратить перегрев.
3. Продукт закончилсяview
3.1 Компоненты
The SENSTREE Dual Probe Temperature & Humidity Controller consists of the main control unit, a temperature probe, and a humidity probe.
Figure 1: Main unit of the SENSTREE Dual Probe Temperature & Humidity Controller, showing the display, control buttons, three power outlets, and connected temperature and humidity probes.
3.2 Основные характеристики
- Dual-Probe Design: Features separate temperature and humidity sensors for independent, precise monitoring and control.
- Двойной дисплей: Clear LCD screen simultaneously shows real-time temperature (°F/°C) and humidity (%).
- Широкое применение: Suitable for greenhouses, reptile terrariums, grow tents, wine cellars, and storage rooms. Compatible with humidifiers, dehumidifiers, heaters, AC units, and fans.
- Точное машиностроение: High-accuracy sensors and advanced calibration ensure reliable performance. Alerts for out-of-range conditions protect sensitive environments.
- Удобный: Simple setup and intuitive buttons for setting desired ranges and automatic device activation.
4. Настройка
4.1 Распаковка
Carefully remove the controller and its components from the packaging. Verify that all parts are present and undamaged.
4.2 Монтаж контроллера
The controller features a hanging design for convenient placement.
Figure 2: The back of the controller unit features keyhole slots for wall mounting using screws (not included).
- Select a suitable location for the controller, ensuring it is away from direct heat sources, moisture, and vibrations.
- Use appropriate screws (not supplied) to secure the controller to a wall or vertical surface using the keyhole slots on the back.
4.3 Подключение зондов
The controller comes with two independent probes: one for temperature and one for humidity.
Figure 3: The separate temperature probe (left) and humidity probe (right) for precise environmental measurements.
- Plug the temperature probe into the designated port on the controller.
- Plug the humidity probe into its designated port.
- Position the probes in the area where you need to monitor temperature and humidity. Ensure they are not obstructed and are representative of the environment you wish to control. The sensor length is approximately 1.4 meters (55.12 inches).
4.4 Включение
- Подключите шнур питания контроллера к стандартной электрической розетке переменного тока 240 В.
- The LCD display will illuminate, showing current temperature and humidity readings.
5. Инструкция по эксплуатации
5.1 Отображение поверхview
The LCD screen provides real-time information and settings.
Figure 4: The controller's backlit LCD display showing temperature (OUT1), humidity (OUT2), and a clock/timer (OUT3).
- ВЫХ1: Displays current temperature and heating/cooling status.
- ВЫХ2: Displays current humidity and humidification/dehumidification status.
- ВЫХ3: Displays current time or timer status.
5.2 Настройка температуры и влажности
To set your desired temperature and humidity ranges:
- Нажмите НАБОР button once to enter temperature setting mode. The temperature display will flash.
- Используйте UP и ВНИЗ arrow buttons to adjust the desired temperature set point.
- Нажимать НАБОР again to confirm the temperature and move to the temperature differential setting (hysteresis). Adjust as needed.
- Нажимать НАБОР a third time to enter humidity setting mode. The humidity display will flash.
- Используйте UP и ВНИЗ arrow buttons to adjust the desired humidity set point.
- Нажимать НАБОР a fourth time to confirm the humidity and move to the humidity differential setting. Adjust as needed.
- Нажимать НАБОР one last time or wait a few seconds for the settings to save automatically and return to normal display.
5.3 Выбор режима
The controller supports various operating modes for temperature and humidity control.
- Нажмите и удерживайте РЕЖИМ button for 3 seconds to enter mode selection.
- Используйте UP и ВНИЗ arrow buttons to cycle through available modes (e.g., Heating, Cooling, Humidification, Dehumidification, Timer).
- Нажимать РЕЖИМ еще раз, чтобы подтвердить свой выбор.
5.4 Функция таймера
The OUT3 port can be configured as a timer. Refer to the detailed instructions in the full manual for specific timer programming steps.
6. Техническое обслуживание
To ensure the longevity and accuracy of your controller:
- Уборка: Протирайте основной блок мягкой сухой тканью. Не используйте абразивные чистящие средства или растворители.
- Уход за зондом: Keep the probes clean and free from debris. Avoid bending or damaging the probe cables.
- Хранилище: If storing the device for an extended period, disconnect it from power and store it in a dry, cool place.
7. Поиск Неисправностей
Распространенные проблемы и способы их решения смотрите в таблице ниже.
| Проблема | Возможная причина | Решение |
|---|---|---|
| Дисплей пустой | No power; power cord loose | Проверьте подключение к электросети; убедитесь, что розетка исправна. |
| Неточные показания | Probes dirty or damaged; incorrect placement | Clean probes; reposition probes away from drafts or direct heat/moisture; check for physical damage. |
| Connected device not activating | Incorrect set points; device not plugged in; controller in wrong mode | Verify set points and differential; ensure device is properly plugged into the correct outlet; check operating mode. |
| Сообщение об ошибке на дисплее | Probe malfunction; internal error | Disconnect and reconnect probes; power cycle the unit. If the error persists, contact customer support. |
8. Технические характеристики
Technical specifications for the SENSTREE Dual Probe Temperature & Humidity Controller:
| Особенность | Спецификация |
|---|---|
| Номер модели | THT1032-ZJ |
| Томtage | 240 вольт (переменный ток) |
| Номинальный ток | 15A max (per plug, check product label for exact rating) |
| Диапазон регулирования температуры | -10°C до 120°C / от 14°F до 248°F |
| Диапазон регулирования влажности | 5-99% ОВ |
| Тип дисплея | ЖК-дисплей |
| Длина зонда | Примерно 1.4 метра (55.12 дюймов) |
| Вес товара | 1.08 фунта |
| Размеры упаковки | 6.65 x 6.3 x 2.05 дюйма |
9. Гарантия и поддержка
The SENSTREE Dual Probe Temperature & Humidity Controller comes with a Гарантия 12 месяца from the date of purchase, covering manufacturing defects. This warranty does not cover damage caused by misuse, accident, unauthorized modification, or improper installation.
For technical support, troubleshooting assistance, or warranty claims, please contact SENSTREE customer service through the retailer where the product was purchased or visit the official SENSTREE webсайт для контактной информации.