VIMIN 10G PCI-E Network Card (Model AQC113) Instruction Manual

Введение

This manual provides detailed instructions for the installation, configuration, and use of your VIMIN 10G PCI-E Network Card. Please read this manual thoroughly before installation to ensure proper operation and to maximize the performance of your network adapter.

Основные характеристики

• 10Gbps RJ45 Copper Port: Equipped with a Marvel AQC113 chipset, offering up to 10Gbps network speed for reliable high-speed data transfer.
• Rapid High-Speed Transmission: Supports PCIe 3.0 x4 bus interface, converting PCIe X4/X8/X16 slots into 10G RJ-45 Ethernet ports for efficient data transfer.
• Multi-Purpose Compatibility: Supports various data rates including 10Gbps, 5Gbps, 2.5Gbps, 1Gbps, and 100Mbps Ethernet connections with intelligent auto-negotiation.
• Flexible Bracket Adaptability: Includes both low-profile and standard brackets for compatibility with diverse computer chassis.
• Seamless System Support: Compatible with Windows 10/11, Windows Server, and Linux operating systems. Drivers are provided via a USB drive.
• Protocol Standard Compliance: Compliant with IEEE 802.3an, IEEE 802.3bz, IEEE 802.3ab, IEEE 802.3u, IEEE 802.3x, IEEE 802.3az, IEEE 802.1Q standards.

Содержимое упаковки

• 1 x VIMIN 10G PCI-E Network Card (AQC113)
• 1 x Standard Profile Кронштейн (предварительно установлен)
• 1 х Low-Profile Кронштейн
• 1 x Driver USB Drive
• 1 x Краткое руководство по установке (Данное руководство является подробным инструкцией)

Установка оборудования

1. Выключите компьютер и отсоедините кабель питания.
2. Откройте корпус компьютера.
3. Locate an available PCI Express x4, x8, or x16 slot on your motherboard.
4. Remove the corresponding slot cover from the computer chassis. If necessary, replace the standard bracket on the network card with the low-profile скобка.
5. Carefully insert the VIMIN 10G PCI-E Network Card into the chosen PCIe slot until it is firmly seated.
6. Secure the network card with a screw to the computer chassis.
7. Закройте корпус компьютера и снова подключите кабель питания.
8. Connect an Ethernet cable to the RJ45 port on the network card.

This image illustrates the three main steps for hardware installation: 1. Opening the chassis and removing the slot limiter. 2. Inserting the PCIe card into the slot. 3. Securing the bracket with screws.

The network card comes with both standard and low-profile brackets to fit various computer cases. It is compatible with PCI Express x4, x8, and x16 slots.

Установка драйвера

После установки оборудования вам потребуется установить соответствующие драйверы для вашей операционной системы.

1. Включите компьютер.
2. Insert the provided USB drive containing the drivers.
3. Navigate to the USB drive and locate the driver folder corresponding to your operating system (Windows, Linux).
4. Follow the on-screen instructions to install the drivers. For Windows, run the setup executable. For Linux, consult the README file within the driver folder for specific commands.
5. После завершения установки драйвера перезагрузите компьютер.

Примечание: In some cases, especially with newer Linux distributions, the driver may be automatically recognized and installed by the system.

Совместимость с операционными системами

The VIMIN 10G PCI-E Network Card supports a wide range of operating systems:

• Виндовс 10
• Виндовс 11
• Windows Server (various versions)
• Linux (various distributions)
• VMware

This network card is compatible with Windows 10/11, Windows Server, and Linux operating systems.

Технические характеристики

Поиск неисправностей

No Network Connection After Installation

• Verify Hardware Installation: Ensure the network card is fully seated in the PCIe slot and securely fastened.
• Проверьте соединение кабеля: Confirm the Ethernet cable is properly connected to both the network card and your router/switch.
• Установка драйвера: Make sure the correct drivers for your operating system have been installed. Refer to the "Driver Installation" section.
• Диспетчер устройств (Windows): Check Device Manager to see if the network card is recognized and if there are any error symbols (e.g., yellow exclamation mark). Reinstall drivers if necessary.
• Настройки BIOS/UEFI: Ensure the PCIe slot is enabled in your system's BIOS/UEFI settings.

Низкая скорость сети

• Качество кабеля: Use a high-quality Cat6a or Cat7 Ethernet cable for 10Gbps connections. Lower category cables may limit speed.
• Совместимость с маршрутизатором/коммутатором: Ensure your network router or switch supports 10Gbps speeds on the connected port.
• Обновления драйверов: Check for the latest drivers from the VIMIN website or the provided USB drive.
• Системные ресурсы: High CPU usage or insufficient RAM on your computer can affect network performance.

Card Not Detected in Windows 11

• Пропускная способность слота PCIe: Some motherboards share bandwidth between PCIe slots and M.2 NVMe slots. If the card is not detected, try moving it to a different PCIe slot or temporarily removing other M.2 devices to check for conflicts.
• Manual Driver Update: If the card appears in Device Manager but has issues, try manually updating the driver by searching for the Intel 10 Gigabit Ethernet driver pack and pointing Device Manager to the extracted driver files.

Гарантия и техническая поддержка

The VIMIN 10G PCI-E Network Card comes with a 1-year after-sale service.

Для получения технической помощи, устранения неполадок или по вопросам гарантии, пожалуйста, свяжитесь с нашей службой поддержки:

• Электронная почта: support@vimintech.com
• Онлайн поддержка: Visit the official VIMIN webсайт для ответов на часто задаваемые вопросы и дополнительных ресурсов.

VIMIN offers dedicated customer support via email at support@vimintech.com, backed by a professional technical team providing 24-hour service.

Информация по безопасности

• Always power off your computer and disconnect the power cable before installing or removing any internal components.
• Handle the network card by its edges to avoid touching the gold-plated connectors or sensitive components.
• Для предотвращения повреждений, вызванных электростатическим разрядом, используйте соответствующие меры предосторожности против статического электричества (например, антистатический браслет).
• Ensure proper ventilation within your computer case to prevent overheating, especially for high-performance components.
• Do not attempt to modify or repair the device yourself. Refer to qualified personnel for service.

Продукт болееview Видео