Zurn P6900-B-L AquaSense Electronics Module with Solenoid Instruction Manual

1. Введение

The Zurn P6900-B-L AquaSense Electronics Module with Solenoid is a replacement component designed for Zurn AquaSense sensor faucets, specifically models Z6912, Z6913, Z6915, and Z6920. This module integrates the solenoid valve, battery pack, and the necessary wiring to connect to the faucet's infrared proximity sensor, enabling hands-free operation. This manual provides instructions for proper installation, operation, and maintenance of the module.

2. Информация по технике безопасности

• Always turn off the water supply to the faucet before beginning any installation or maintenance.
• Disconnect electrical power if applicable before servicing.
• Носите соответствующие средства индивидуальной защиты, такие как защитные очки и перчатки.
• Убедитесь, что все соединения надежны и не допускайте утечек.
• Утилизируйте старые батареи ответственно в соответствии с местными правилами.

3. Содержимое упаковки

Перед началом установки убедитесь, что все компоненты присутствуют:

• Zurn P6900-B-L AquaSense Electronics Module with Solenoid
• Battery Pack (integrated)
• 4 щелочные батарейки типа АА (в комплекте)
• Connecting Wire to Faucet Sensor
• Small Hex Key/Wrench (for securing connections, if applicable)
• O-ring (for sealing connections, if applicable)

4. Настройка и установка

Follow these steps to install the Zurn P6900-B-L Electronics Module:

1. Отключите подачу воды: Locate the main water shut-off valve for the faucet and turn it off completely.
2. Disconnect Old Module (if replacing): Carefully disconnect the existing electronics module from the faucet sensor and water lines. Be prepared for residual water.
3. Prepare New Module: Ensure the new P6900-B-L module has the included 4 AA alkaline batteries properly installed in the battery compartment.
4. Подключите водопроводные линии: Attach the solenoid valve portion of the new module to the appropriate hot and cold water supply lines. Use thread sealant tape or pipe dope as recommended by local plumbing codes. Ensure connections are hand-tight, then use a wrench for a final quarter-turn, avoiding overtightening.
5. Подключите провод датчика: Carefully connect the wire from the electronics module to the faucet's infrared proximity sensor. The connector pins are delicate; align them precisely to avoid bending. Removing any rubber o-ring on the connector might assist in feeling for a solid connection, as a coupler nut typically secures the pieces.
6. Безопасный модуль: Mount or secure the electronics module in a suitable location, typically under the sink, ensuring it is protected from moisture and easily accessible for future maintenance.
7. Восстановление водоснабжения: Slowly turn the main water supply back on and check for any leaks at all connection points.
8. Тестовая операция: Activate the faucet sensor to verify proper water flow and shut-off.

5. Инструкция по эксплуатации

The Zurn AquaSense Electronics Module controls water flow in conjunction with the faucet's infrared proximity sensor. To operate the faucet:

• Активация: Place your hands within the detection range of the faucet's sensor. The sensor will detect your presence.
• Расход воды: Upon detection, the electronics module will activate the solenoid valve, allowing water to flow from the faucet.
• Деактивация: Remove your hands from the sensor's detection range. The module will then close the solenoid valve, stopping the water flow.

The system is designed for hands-free operation, promoting hygiene and water conservation.

6. Техническое обслуживание

Regular maintenance ensures optimal performance and longevity of your Zurn AquaSense Electronics Module.

6.1. Замена батареи

The module is powered by 4 AA alkaline batteries. When the batteries are low, the faucet may exhibit inconsistent operation or cease to function. To replace the batteries:

1. Отключите подачу воды: Отключаем подачу воды в кран.
2. Доступ к батарейному отсеку: Locate the battery compartment on the electronics module. This is typically secured with a cover.
3. Извлеките старые батареи: Open the compartment and remove the old AA batteries.
4. Вставьте новые батареи: Insert four new AA alkaline batteries, ensuring correct polarity (+/-).
5. Защищенный отсек: Закройте и зафиксируйте крышку батарейного отсека.
6. Восстановите водоснабжение и проведите испытания: Turn the water supply back on and test the faucet's operation.

6.2. Уборка

Periodically inspect the module and connections for any signs of corrosion or debris. Clean the exterior of the module with a soft, damp Ткань. Не используйте абразивные чистящие средства или растворители.

7. Поиск Неисправностей

If your Zurn AquaSense faucet is not functioning correctly, refer to the following table for common issues and solutions:

8. Технические характеристики

9. Гарантия и поддержка

The Zurn P6900-B-L AquaSense Electronics Module is covered by a limited manufacturer's warranty. For specific warranty terms and conditions, please refer to the documentation provided with your original Zurn product or visit the official Zurn webсайт.

For technical support, replacement parts, or further assistance, please contact Zurn Customer Service:

• Webсайт: www.zurn.com
• Контактная информация: Refer to the 'Contact Us' section on the Zurn webсайт для получения телефонных номеров и поддержки по электронной почте.