SIMON Series 10 Double Switch-Commutator Instruction Manual

1. Продукт закончилсяview

The SIMON Series 10 Double Switch-Commutator is designed to control two independent light points from a single location. It can function as a standard ON/OFF switch or as a commutator, redirecting electrical current to connect different circuits. This unit is supplied as a pre-assembled component, including the mechanism, cover, and frame, to simplify the installation process. Its minimalist design with straight lines allows for seamless integration into various interior spaces.

Рисунок 1: Передняя часть view of the SIMON Series 10 Double Switch-Commutator.

2. Предупреждения о безопасности

• Опасность поражения электрическим током: Installation should only be performed by a qualified electrician or a person with adequate knowledge of electrical systems. Always disconnect the main power supply before beginning any installation or maintenance work.
• Do not drill into the device or expose it to fire.
• This product is designed for indoor use (IP20 rating). Do not install in environments with high humidity or direct water exposure.
• Убедитесь, что все соединения электропроводки надежны и соответствуют местным электротехническим нормам.
• Under no circumstances shall Simon be liable for any indirect, special, incidental, punitive, or consequential damages of any kind arising from improper installation or misuse of the product.

3. Входящие в комплект компоненты

The SIMON Series 10 Double Switch-Commutator package includes the following components:

• Double Switch-Commutator Mechanism
• Decorative Cover (White)
• Монтажная рамка

Figure 2: Product as supplied in its packaging.

4. Настройка и установка

The SIMON Series 10 Double Switch-Commutator is designed for straightforward installation. The metallic frame provides robustness, while the polypropylene frame offers flexibility during mounting.

4.1 Схема электропроводки и соединений

This device uses screw terminals for secure wiring connections. Refer to the diagram below for proper wiring. If you are unfamiliar with electrical wiring, consult a professional electrician.

Рисунок 3: В разобранном виде view showing the mechanism, frame, and cover assembly.

1. Подготовка: Ensure the main power supply to the circuit is turned OFF at the consumer unit/fuse box.
2. Монтаж механизма: Place the switch mechanism into the wall box. The flexible polypropylene frame aids in positioning.
3. Проводка: Connect the electrical wires to the screw terminals. For a double switch-commutator, typically you will have a common phase wire (L) and two switched phase wires (L1, L2) for each light point, along with neutral and earth connections if applicable to the installation type. Ensure all connections are tight.
4. Обеспечение: Use the metallic claws to firmly secure the mechanism to the wall box.
5. Attaching the Cover and Frame: Snap the decorative cover and frame onto the mechanism until they are securely in place.
6. Окончательная проверка: Once installation is complete, restore power and test the functionality of both switches.

5. Инструкция по эксплуатации

The SIMON Series 10 Double Switch-Commutator features two independent rocker switches. Each switch can control a separate light point or circuit.

• Функция переключателя: Press the top part of the rocker to turn the connected light/circuit ON. Press the bottom part to turn it OFF.
• Commutator Function: When configured as a commutator, pressing the rocker will switch the current path between two different conductors, allowing control of a light from multiple locations (e.g., at the top and bottom of a staircase).

6. Техническое обслуживание

The SIMON Series 10 Double Switch-Commutator requires minimal maintenance.

• Уборка: To clean the surface, gently wipe with a soft, dry cloth. For stubborn marks, use a slightly damp Протрите тканью, смоченной мягким мылом, и сразу же вытрите насухо.
• Избегать: Не используйте абразивные чистящие средства, растворители или едкие химикаты, так как они могут повредить отделку.
• Инспекция: Periodically check for any loose connections or signs of wear. If any damage is observed, disconnect power and replace the unit.

7. Поиск Неисправностей

If the switch-commutator is not functioning as expected, consider the following:

• Нет питания: Check the main power supply and the circuit breaker. Ensure power is restored to the circuit.
• Свет не включается/выключается: Verify that the light bulb is functional. Check all wiring connections at the switch and the light fixture for looseness or incorrect wiring.
• Прерывистая работа: This could indicate a loose connection. Disconnect power and re-check all screw terminals.
• Difficulty in Wiring: The wiring diagram on the mechanism can be complex for some users. If you encounter difficulties, it is recommended to consult a qualified electrician.

8. Технические характеристики

9. Гарантия и поддержка

For warranty information or technical support, please contact Simon customer service. Keep your purchase receipt as proof of purchase.

Visit the official Simon website for additional resources, FAQs, or to locate authorized service centers.