KKmoon KKM828 2-in-1 Digital Multimeter with Oscilloscope User Manual

1. Введение

The KKmoon KKM828 is a versatile 2-in-1 device combining the functionalities of a digital multimeter and an oscilloscope. Designed for efficiency and accuracy, it features a 2.4-inch color display, a 1MHz bandwidth for AC voltage, and a 2.5Msps real-time sampling rate. This manual provides essential information for safe and effective operation of your KKM828 device.

2. Информация по технике безопасности

Please read and understand all safety instructions before using the device. Failure to follow these instructions may result in electric shock, fire, or damage to the device or other equipment.

• Always ensure the device is in good working condition and free from damage before use.
• Не применять объемtage or current that exceeds the maximum limits specified in the technical specifications.
• Будьте осторожны при работе с томомtages above 24V, as they pose a shock hazard. The device will emit an audible warning if the input voltagе превышает 24 В.
• Перед проведением измерений убедитесь, что выбраны правильная функция и диапазон.
• При появлении индикатора низкого заряда батареи немедленно заменяйте ее, чтобы обеспечить точность показаний.
• The device is equipped with double fuses (500mA/250V and 10A/250V) for protection. Do not bypass or use incorrect fuse types.
• Не используйте устройство во влажных условиях или во взрывоопасных средах.
• Refer to the "Maintenance" section for proper cleaning and storage procedures.

3. Продукт закончилсяview

The KKmoon KKM828 integrates a digital multimeter and an oscilloscope into a compact, handheld unit. Key components and features are detailed below.

3.1 Основные характеристики

• 2-в-1 Функциональность: Combines a digital multimeter and an oscilloscope.
• Отображать: 2.4-inch 320x240 LCM color screen for clear readings and waveform display.
• Oscilloscope Performance: 1MHz ACV bandwidth, 2.5Msps real-time sampскорость.
• Функции мультиметра: Измеряет переменный/постоянный токtagнапример, переменный/постоянный ток, сопротивление, емкость, частота, коэффициент заполнения, диод и целостность цепи.
• Хранение данных: Stores up to 100 sets of data and 10 waveforms.
• Пользовательский интерфейс: Silicone buttons and a pressure-sensitive dial for precise function selection.
• Эргономика: Integrated back bracket for a 60° viewугол наклона.
• Безопасность: Double fuse protection (500mA/250V, 10A/250V) and input voltagе предупреждение.

3.2 Компоненты устройства

Обратитесь к изображению ниже для более подробной информации.view of the device's main components.

Figure 1: KKM828 Product Details. This image highlights the device's HD color screen (01), the function dial for accurate gear changes (02), and the back bracket (03) for easy viewинж.

• HD-экран: 2.4-inch color screen for clear display of measurements and waveforms.
• Функциональный диск: Rotary switch for selecting measurement functions (voltage, current, resistance, etc.) and oscilloscope mode.
• Buttons (F1-F4, R, S): Used for navigating menus, selecting ranges, holding data, and other specific functions.
• Входные разъемы: Terminals for connecting test leads for various measurements (e.g., VΩHz, mA, 10A, COM).
• Задний кронштейн: Foldable stand for propping up the device at a 60° angle for convenient viewинж.

4. Настройка

4.1 Установка аккумулятора

The KKM828 requires three AA batteries for operation. Ensure the device is powered off before installing or replacing batteries.

1. Найдите крышку батарейного отсека на задней панели устройства.
2. Open the battery compartment cover by sliding or unscrewing it (if applicable).
3. Insert three AA batteries, observing the correct polarity (+ and -) as indicated inside the compartment.
4. Плотно закройте крышку батарейного отсека.

4.2 Включение/выключение питания

To power on the device, rotate the function dial from the "OFF" position to any desired measurement function. To power off, rotate the dial back to the "OFF" position.

5. Инструкция по эксплуатации

5.1 Функции мультиметра

The KKM828 offers a comprehensive range of multimeter measurement capabilities. Always connect test leads correctly to the appropriate input jacks (e.g., COM, VΩHz, mA, 10A) for the selected function.

• Переменный / постоянный токtagд Измерение: Rotate the dial to the 'V~' or 'V=' position. Connect test leads in parallel with the circuit.
• Измерение переменного/постоянного тока: Rotate the dial to the 'mA~', 'mA=', '10A~', or '10A=' position. Connect test leads in series with the circuit.
• Измерение сопротивления: Rotate the dial to the 'Ω' position. Ensure the circuit is de-energized before measuring resistance.
• Измерение емкости: Rotate the dial to the 'mF' position. Discharge capacitors before measurement.
• Измерение частоты и коэффициента заполнения: Rotate the dial to the 'Hz%' position.
• Диодный Тест: Rotate the dial to the 'Diode' position. Connect leads across the diode to check forward voltagе падение.
• Тест на непрерывность: Rotate the dial to the 'Continuity' position. The device will beep if resistance is below approximately 50Ω.

Рисунок 2: Пример измерения мультиметром.ampлес. This image illustrates the display during Frequency, Duty Cycle, Diode Test, and Continuity measurements, demonstrating the device's various multimeter functions.

5.2 Функции осциллографа

The KKM828 features a convenient one-button oscilloscope for waveform analysis.

1. Rotate the function dial to the 'Graphical' (oscilloscope) mode.
2. Connect the test leads to the circuit where you wish to observe the waveform.
3. The device will automatically display the waveform. Use the secondary display at the bottom to view parameters such as Peak-to-Peak voltage (VP-P), average value, RMS value, frequency, time base, and ampдолгота.
4. Measurement modes include 'Normal' and 'Automatic'. The device can quickly and accurately measure and display waveforms.

Figure 3: Oscilloscope Waveform Display. На этом изображении показан эксamples of different electrical waveforms (sine, square, pulse, complex) as displayed on the KKM828's oscilloscope screen, along with key measurement parameters.

5.3 Хранение и восстановление данных

The KKM828 can store up to 100 sets of measurement data and 10 waveforms for later review.

• Specific instructions for saving and recalling data are typically accessed via the function buttons (e.g., 'S' for Save, 'R' for Recall) in relevant measurement modes. Refer to the on-screen prompts for detailed operation.
• The device allows for simultaneous display of historical records and real-time data for easy comparison and analysis.

6. Техническое обслуживание

6.1 Очистка

Для очистки устройства протрите его.asinг с объявлениемamp cloth and a mild detergent. Do not use abrasive cleaners or solvents. Ensure the device is powered off and disconnected from any circuits before cleaning. Do not allow moisture to enter the device.

6.2. Замена батареи

When the low battery indicator appears on the display, replace the three AA batteries as described in the "Battery Installation" section (4.1). Always use fresh batteries of the same type.

6.3 Хранение

When not in use for extended periods, remove the batteries to prevent leakage. Store the device in a cool, dry place within the specified storage environment: -10°C to 60°C, with relative humidity less than 90% RH.

7. Поиск Неисправностей

This section addresses common issues you might encounter with your KKM828 device.

8. Технические характеристики

The following table details the technical specifications of the KKmoon KKM828.