1. Введение
The SENSTREE WTC100 is a wireless digital plug-in thermostat designed for automatic temperature control of various electrical heating or cooling appliances. It allows users to set target temperatures to automatically activate or deactivate connected devices, maintaining a stable environment. This manual provides essential information for the safe and effective use of your WTC100 controller.
2. Информация по технике безопасности
- Перед использованием прочтите все инструкции.
- Ensure the device is properly grounded. The receiver features a 3-prong grounded terminal.
- Do not exceed the maximum load capacity of 15A (1500W at 110V, 3000W at 220V).
- Do not immerse the remote controller or receiver in water or expose them to excessive moisture.
- Хранить в недоступном для детей месте.
- Не разбирайте и не пытайтесь ремонтировать устройство. В случае необходимости обслуживания обратитесь в службу поддержки клиентов.
- Replace batteries in the remote controller promptly when the low battery indicator appears to ensure continuous operation.
3. Продукт закончилсяview
The WTC100 system consists of two main components: a wireless remote controller and a plug-in receiver outlet.
Figure 3.1: WTC100 Remote Controller and Plug-in Receiver
3.1. Пульт дистанционного управления
- ЖК-дисплей: Shows current temperature, set temperatures, and operating mode.
- Кнопки управления: SET, Up, Down, M (Mode) for configuration.
- Встроенный датчик температуры: Detects ambient temperature for control.
- Отсек для батареи: For 2x AAA batteries (not included).
Figure 3.2: Remote Controller with integrated temperature sensor
3.2. Plug-in Receiver
- Розетка: Connects to your heating or cooling appliance.
- Кнопка ручного включения/выключения: Allows manual control of the connected appliance.
- Световой индикатор: Shows power status and connection.
Figure 3.3: Receiver with plug and specification label
4. Настройка
4.1. Install Batteries in Remote Controller
- Откройте крышку батарейного отсека на задней панели пульта дистанционного управления.
- Вставьте две (2) батарейки типа AAA, соблюдая правильную полярность (+/-).
- Закройте крышку батарейного отсека.
4.2. Подключите приемник.
- Plug the WTC100 receiver into a standard 3-prong wall outlet.
- Plug your heating or cooling appliance into the outlet on the receiver.
4.3. Сопряжение (при необходимости)
The remote controller and receiver are typically pre-paired at the factory. If they do not connect automatically, follow these steps:
- Ensure both the remote and receiver are powered on.
- Press and hold the power button on the receiver for 3-5 seconds until the indicator light flashes.
- Within 10 seconds, press any button on the remote controller. The indicator light on the receiver will stop flashing and remain solid, indicating successful pairing.
5. Инструкция по эксплуатации
5.1. Включение/выключение питания
- Пульт дистанционного управления: The remote is always on to display temperature.
- Получатель: Press the power button on the receiver to manually turn the connected appliance ON or OFF.
5.2. Переключение единиц измерения температуры (°C/°F)
Figure 5.1: Switching between Celsius and Fahrenheit
To switch between Celsius (°C) and Fahrenheit (°F), press and hold the 'UP' arrow button on the remote controller for approximately 3 seconds.
5.3. Setting Operating Mode (Heating/Cooling)
Figure 5.2: Cooling and Heating Mode Switchable
Press the 'M' (Mode) button on the remote controller to toggle between Heating Mode and Cooling Mode. The display will indicate the active mode.
5.4. Setting Target Temperatures
The WTC100 allows you to set both an 'ON' temperature and an 'OFF' temperature for precise control.
- Press the 'SET' button once. The 'ON' temperature will flash. Use the 'UP' or 'DOWN' arrows to adjust the desired 'ON' temperature.
- Press the 'SET' button again. The 'OFF' temperature will flash. Use the 'UP' or 'DOWN' arrows to adjust the desired 'OFF' temperature.
- Press 'SET' a third time or wait a few seconds for the settings to save automatically.
Heating Mode Exampль: If 'ON' is set to 68°F and 'OFF' is set to 72°F, the heater will turn on when the temperature drops to 68°F and turn off when it reaches 72°F.
Video 5.3: Demonstration of setting Heating Mode with the WTC100. This video illustrates how to configure the thermostat to activate a heating device when the temperature falls below a set point and deactivate it when it rises above another set point.
Cooling Mode Exampль: If 'ON' is set to 78°F and 'OFF' is set to 74°F, the cooling device will turn on when the temperature rises to 78°F and turn off when it drops to 74°F.
Figure 5.4: WTC100 controlling a window air conditioner in Cooling Mode
6. Техническое обслуживание
- Уборка: Wipe the remote and receiver with a soft, dry cloth. Do not use abrasive cleaners or solvents.
- Замена батареи: When the low battery indicator appears on the remote's display, replace both AAA batteries immediately to ensure accurate temperature readings and continuous control.
7. Поиск Неисправностей
| Проблема | Возможная причина | Решение |
|---|---|---|
| Remote display is blank or dim. | Низкий заряд или полная разрядка батарей. | Replace AAA batteries in the remote controller. |
| Приёмник не отвечает на пульт дистанционного управления. | Не сопряжено, вне зоны действия или с помехами. | Re-pair the remote and receiver (see Section 4.3). Ensure remote is within 100m (open space) of the receiver. Avoid strong electromagnetic interference. |
| Connected appliance not turning ON/OFF at set temperatures. | Incorrect mode (Heating/Cooling), incorrect set temperatures, or appliance issue. | Verify the correct operating mode is selected. Check and adjust 'ON' and 'OFF' temperatures. Ensure the appliance itself is functioning correctly. |
| Показания температуры кажутся неточными. | Remote sensor obstructed or exposed to direct heat/cold. | Ensure the remote controller's sensor (located at the top) is not covered and is placed in an area representative of the desired ambient temperature. |
| Часто звучит будильник. | High/low temperature alarm thresholds reached. | The WTC100 features high and low temperature alarms. Consult the full product manual for specific alarm settings and how to adjust or temporarily mute them. |
8. Технические характеристики
| Особенность | Деталь |
|---|---|
| Название модели | ВТЦ100 |
| Vol входtage | 100-240 В переменного тока |
| Максимальный выходной ток | 15А |
| Максимальная выходная мощность | 1500 Вт при 110 В / 3000 Вт при 220 В |
| Тип контроля температуры | Программируемый |
| Технология связи | Беспроводная связь (РЧ) |
| Расстояние дистанционного управления | До 100 м (открытое пространство) |
| Датчик температуры | Built-in to Remote Controller |
| Тип дисплея | ЖК-дисплей с подсветкой |
| Источник питания (дистанционный) | 2 батарейки ААА (не входят в комплект) |
| Mounting Type (Remote) | Wall Mount, Handheld |
9. Гарантия и поддержка
SENSTREE products are designed for reliability and performance. For warranty information, technical support, or service inquiries, please refer to the contact information provided with your product packaging or visit the official SENSTREE webсайт. Пожалуйста, сохраните доказательство покупки для гарантийных претензий.