Rakstore ZB2L3 Battery Capacity Tester User Manual

1. Введение

The Rakstore ZB2L3 Battery Capacity Tester is a versatile device designed to measure the capacity of various battery types, including 18650 Lithium batteries and Lead-Acid batteries. It functions as a discharge tester, allowing users to determine the actual capacity by discharging the battery through a load and measuring the discharged energy. This manual provides detailed instructions for the safe and effective use of the ZB2L3 tester.

2. Информация по технике безопасности

• Always ensure correct polarity when connecting batteries to avoid damage to the tester and battery.
• Use appropriate discharge loads. Overloading the tester or using incorrect loads can cause overheating and damage.
• Не замыкайте клеммы аккумулятора.
• Operate the device in a well-ventilated area, especially when discharging batteries, as they can generate heat.
• Берегите устройство от влаги и экстремальных температур.
• Это устройство не игрушка. Храните в недоступном для детей месте.

3. Особенности продукта

• Источник питания: DC4.5-6V via micro USB interface.
• Рабочий ток: Less than 70mA.
• Объем разрядаtage Диапазон: 1-15V with 0.01V resolution.
• Прекращение Томаtage Диапазон: 0.5-11.0В.
• Supported Discharge Current: Up to 3.000A with 0.001A resolution.
• Томtage Ошибка измерения: Less than 1% + 0.02V.
• Ошибка измерения тока: Less than 1.2% ± 0.002A.
• Диапазон емкости аккумулятора: Up to 9999Ah (1Ah=1000mAh). Display adjusts decimal point for large values (e.g., X.XXX Ah, XX.XX Ah).
• Компактный размер: Circuit board 50mm x 37mm, finished product 50mm x 37mm x 17mm (L x W x H, including copper foot height).

4. Содержимое упаковки

• 1 x Rakstore ZB2L3 Battery Capacity Tester Unit
• (Note: Discharge resistors and battery holders are typically sold separately and are required for operation.)

5. Настройка

Before operating the ZB2L3 tester, ensure all connections are made correctly.

Figure 1: ZB2L3 Battery Capacity Tester showing the micro USB power input, battery terminals, and load terminals.

1. Подключение источника питания: Connect a DC 4.5-6V power source to the micro USB port on the tester. A standard phone charger or power bank can be used. The display should light up.
2. Подключение аккумулятора: Connect the battery to be tested to the "BAT+" and "BAT-" terminals. Ensure correct polarity. The tester will display the current battery voltage.
3. Discharge Load Connection: Connect an appropriate discharge resistor (load) to the "LOAD+" and "LOAD-" terminals. The resistance value of the load will determine the discharge current. Ensure the load can handle the expected power dissipation.

Важный: The discharge current should not exceed 3.000A. Calculate the required resistance using Ohm's Law (R = V/I) and Power Law (P = V*I or P = I²*R) to ensure the resistor can handle the power. For example, if testing a 3.7V battery at 1A, you need a 3.7 Ohm resistor capable of dissipating at least 3.7W.

6. Инструкция по эксплуатации

Follow these steps to perform a battery capacity test:

Figure 2: ZB2L3 Battery Capacity Tester showing the 'OK', '+', and '-' buttons for operation.

1. Начальный дисплей: After connecting the power and battery, the tester will display the battery's current voltage.
2. Set Termination Voltage:
   • Press the "OK" button once. The display will show the current termination voltage (e.g., "U 3.00").
   • Use the "+" and "-" buttons to adjust the termination voltagе. Это томtage at which the discharge test will stop. For 18650 Lithium batteries, a common termination voltage is 3.0V. For Lead-Acid batteries, consult the battery's specifications.
   • Press "OK" again to confirm the setting and return to the main display.
3. Start Discharge Test:
   • With the battery and load connected, and the termination voltage set, press and hold the "OK" button for approximately 3 seconds.
   • The tester will begin discharging the battery through the connected load. The display will cycle through current voltage (V), discharge current (A), and accumulated capacity (Ah).
4. Monitor Test Progress: Observe the display. The voltage will gradually decrease, and the accumulated capacity will increase.
5. Test Completion: The test will automatically stop when the battery voltage reaches the set termination voltage. The display will then show the final accumulated capacity (Ah) and flash.
6. View Результаты: After the test stops, you can press the "OK" button to cycle through the final voltage, current, and capacity readings.
7. Reset for New Test: To start a new test, disconnect the battery and load, then reconnect them, or simply press and hold the "OK" button again to clear the previous results and start a new cycle.

7. Техническое обслуживание

• Уборка: Для очистки устройства используйте мягкую сухую ткань. Не используйте жидкие чистящие средства или растворители.
• Хранилище: Храните тестер в прохладном, сухом месте, вдали от прямых солнечных лучей и экстремальных температур.
• Инспекция: Periodically check the terminals and connections for any signs of wear or damage.

8. Поиск Неисправностей

9. Технические характеристики

10. Гарантия и поддержка

This product is manufactured by Rakstore. For any technical support or warranty inquiries, please refer to the retailer where the product was purchased or visit the official Rakstore webсайт для контактной информации.

Пожалуйста, сохраните документ, подтверждающий покупку, для претензий по гарантии.