MIPRO ACT-5802/ACT-58H2 Digital Wireless Microphone System User Manual

Введение

This manual provides detailed instructions for the setup, operation, and maintenance of your MIPRO ACT-5802/ACT-58H2 Digital Wireless Microphone System. This system features a 5 GHz 1/2U dual-channel digital receiver and two ISM 5 GHz digital handheld wireless microphones, designed for reliable and high-quality audio transmission.

Что в коробке?

После распаковки, пожалуйста, убедитесь в наличии всех следующих компонентов:

• 1 x ACT-5802 Dual-Channel Digital Receiver
• 2 x ACT-58H2 Handheld Digital Wireless Microphones
• 1 адаптер питания для ресивера
• 2 x Антенны
• 1 аудиокабель
• 1 х Руководство пользователя

Note: If any items are missing or damaged, please contact your dealer immediately.

Продукт болееview

The MIPRO ACT-5802/ACT-58H2 system provides a robust wireless audio solution. Below is an image of the complete system.

Рисунок 1: MIPRO ACT-5802/ACT-58H2 Digital Wireless Microphone System. This image displays the ACT-5802 dual-channel receiver unit and two ACT-58H2 handheld microphones, illustrating the primary components of the wireless audio system.

Инструкции по установке

1. Receiver Setup (ACT-5802)

1. Размещение: Position the receiver on a stable, flat surface, away from potential sources of interference such as Wi-Fi routers, microwave ovens, or other 5 GHz devices. Ensure adequate ventilation.
2. Антенное соединение: Connect the two supplied antennas to the ANTENNA A and ANTENNA B connectors on the rear panel of the receiver. Ensure they are securely tightened.
3. Подключение питания: Connect the power adapter to the DC IN jack on the rear panel of the receiver, then plug the adapter into an appropriate AC power outlet.
4. Подключение аудиовыхода: Подключите аудиовыход ресивера (XLR или 1/4"-разъем) к входу микшера. amplifier, or audio recording device using the supplied audio cable.

2. Handheld Microphone Setup (ACT-58H2)

1. Установка аккумулятора: Unscrew the lower part of the microphone body to reveal the battery compartment. Insert two fresh AA batteries, observing the correct polarity (+/-) as indicated inside the compartment. Screw the lower part back on securely.
2. Включение питания: Нажмите и удерживайте кнопку питания на микрофоне, пока не загорится дисплей.
3. Pairing (ACT Sync):
   • On the receiver, select the desired channel (e.g., Channel 1 or Channel 2) using the control buttons.
   • Press the "ACT" button on the receiver. The ACT indicator will flash.
   • Align the microphone's IR window with the receiver's IR window (usually located on the front panel) within 30 cm (1 foot).
   • The microphone will automatically sync with the receiver. Once synced, the receiver's ACT indicator will stop flashing, and the microphone's display will show the matched channel.

Инструкция по эксплуатации

1. Включение и выключение

• Получатель: Press the power button on the front panel. The OLED display will illuminate.
• Микрофон: Press and hold the power button until the display illuminates (on) or turns off (off).

2. Channel Selection and Adjustment

• The ACT-5802 receiver allows for automatic frequency scanning to find clear channels. Refer to the receiver's display and menu buttons for navigation.
• Once a clear channel is selected on the receiver, use the ACT Sync function (as described in Setup) to pair the microphone to the new channel.

3. Регулятор громкости

• Уровень выходного сигнала приемника: Adjust the volume knob on the front panel of the ACT-5802 receiver to control the audio output level sent to your mixer or ampпожизненнее.
• Усиление микрофона: Some microphones may have internal gain adjustments. Consult the microphone's specific instructions if needed. Generally, start with a moderate gain setting.

4. Отображение информации

The OLED display on both the receiver and microphones provides critical information such as channel number, frequency, battery status, and RF/AF signal strength. Monitor these displays during operation for optimal performance.

Обслуживание

1. Уборка

• Use a soft, dry cloth to clean the exterior surfaces of the receiver and microphones.
• Не используйте жидкие чистящие средства, растворители или абразивные материалы, так как они могут повредить покрытие или внутренние компоненты.
• For microphone grilles, gently wipe with a slightly damp ткань и убедитесь, что она полностью высохла перед использованием.

2. Уход за аккумулятором

• Always remove batteries from the microphones if they will not be used for an extended period to prevent leakage and damage.
• Replace batteries promptly when the low battery indicator appears on the microphone's display.
• Используйте высококачественные щелочные или перезаряжаемые батарейки типа АА.

3. Хранение

• Храните систему в прохладном, сухом месте, вдали от прямых солнечных лучей, экстремальных температур и высокой влажности.
• Keep the original packaging for safe transport and storage.

Поиск неисправностей

Технические характеристики

Гарантия и поддержка

Для получения информации о гарантии и технической поддержке, пожалуйста, обратитесь к гарантийному талону, прилагаемому к вашему изделию, или посетите официальный сайт MIPRO. webСохраните чек о покупке в качестве подтверждения покупки на случай предъявления гарантийных претензий.

For further assistance, contact your authorized MIPRO dealer or distributor.