Thincol Digital Temperature Controller (12V Model) User Manual

1. Введение

This manual provides detailed instructions for the installation, operation, and maintenance of your Thincol Digital Temperature Controller (12V Model). Please read this manual thoroughly before using the device to ensure proper function and safety.

2. Информация по технике безопасности

Важные инструкции по технике безопасности:

• Убедитесь, что источник питания vol.tage matches the device's requirements (DC 12V for this model).
• Не подвергайте устройство воздействию воды или чрезмерной влажности.
• Avoid installing the device in areas with extreme temperatures or direct sunlight.
• Перед выполнением любых работ по электропроводке или техническому обслуживанию отключите питание.
• All wiring should be performed by a qualified professional if you are unsure.
• Хранить в недоступном для детей месте.

3. Содержимое упаковки

Пакет должен содержать следующие элементы:

• 1 x Thincol Digital Thermostat Temperature Alarm Controller Sensor (12V Model)

4. Продукт закончилсяview

Familiarize yourself with the components of your temperature controller.

Рисунок 1: Передняя часть view of the Thincol Digital Temperature Controller, showing the dual LED display (PV and SV), 'SET' button, up/down arrows, 'OUT' indicator, and 'Restart' button. The temperature sensor probe is connected via a black wire.

Рисунок 2: Сзади view of the Thincol Digital Temperature Controller, highlighting the blue screw terminals for power input and output connections.

Рисунок 3: Сторона view of the Thincol Digital Temperature Controller, showing its compact form factor suitable for panel mounting.

Ключевые компоненты:

• Отображение фотоэлектрических систем: Process Value (Current Temperature)
• Дисплей SV: Set Value (Target Temperature)
• Кнопка SET: Enters/Exits parameter setting mode.
• Кнопки вверх / вниз: Adjust values in setting mode.
• Выходной индикатор: Illuminates when the output relay is active.
• Кнопка перезапуска: Сбрасывает устройство.
• Клеммы проводки: For power input and load output connections.
• Датчик температуры: Measures the ambient temperature.

5. Технические характеристики

6. Настройка и подключение

Before wiring, ensure the power supply is disconnected. Incorrect wiring can damage the device or connected equipment. If you are unsure, consult a qualified electrician.

Соединения проводки:

1. Потребляемая мощность: Connect the DC 12V power supply to the designated input terminals on the back of the controller. Observe polarity (+/-) carefully.
2. Загрузка выходных данных: Connect the device you wish to control (e.g., heating element, cooling fan) to the output terminals. The controller acts as a switch for this load. Ensure the load's power requirements do not exceed the controller's maximum output (120W for the 12V model).
3. Датчик температуры: Insert the temperature sensor probe into the environment where temperature measurement is required. Ensure it is securely placed and not directly exposed to heat sources or drafts that could skew readings.

Warning: Always disconnect power before making or changing any wiring connections.

7. Инструкция по эксплуатации

Setting the Target Temperature (SV):

1. Нажмите НАБОР button once. The SV (Set Value) display will begin to flash.
2. Используйте Up и Вниз arrow buttons to adjust the target temperature to your desired value.
3. Нажмите НАБОР button again to confirm the setting and exit the setting mode.

Cooling/Heating Mode Selection:

The controller can operate in either cooling or heating mode. This is typically configured via an advanced parameter (often labeled P0 or P1). Please consult the full product manual for specific instructions on how to access and set the cooling or heating mode.

Advanced Parameter Settings (P3, P4, P5):

To access advanced parameters, typically a long press of the НАБОР button is required. Use the Up/Down buttons to navigate between parameters (e.g., P0, P1, P2, P3, P4, P5) and then press НАБОР again to enter the parameter's value adjustment mode.

• P3 Setting (Delay Stop/Compressor Protection): If P3 is set to '1', the thermostat will stop running for 1 minute. This function is often used for compressor delay protection in cooling systems. A long press of the НАБОР button is required to trigger this function again after it has completed its cycle.
• P4 Setting (Delayed Start): If P4 is set to '1', the thermostat will begin operation after a 1-minute delay. During this delay, the digital display will not illuminate until normal operation commences. A long press of the НАБОР button is required to trigger this function again.
• P5 Setting (Parameter Lock): By default, P5 is set to 'OFF'. Once the desired temperature and other parameters are configured, setting P5 to 'ON' will lock the data, preventing accidental changes. To modify settings again, P5 must be set back to 'OFF'.

Калибровка температуры:

The device supports temperature calibration to fine-tune accuracy. This is usually an advanced parameter (e.g., P7 or P8). Refer to the full product manual for specific instructions on how to access and adjust the temperature calibration offset.

High/Low Limit Temperature Setting:

The controller allows setting upper and lower temperature limits to prevent extreme conditions. These are typically accessible through advanced parameters. Consult the full product manual for details on setting these limits.

8. Техническое обслуживание

• Уборка: Протирайте устройство мягкой сухой тканью. Не используйте абразивные чистящие средства или растворители.
• Уход за датчиком: Ensure the temperature sensor is clean and free from debris for accurate readings.
• Проверка связи: Периодически проверяйте надежность всех соединений проводки.
• Хранилище: If storing the device for an extended period, disconnect it from power and store it in a dry, cool place.

9. Поиск Неисправностей

10. Гарантия и поддержка

For warranty information and technical support, please refer to the documentation provided with your purchase or contact Thincol customer service directly. Keep your purchase receipt for warranty claims.

Manufacturer: Thincol