VOTRONIC VCC 1212-45 IUoU-Li Isolated 12V 45A B2B Charger

1. Введение

The VOTRONIC VCC 1212-45 is an isolated B2B (Battery-to-Battery) charge booster designed for universal use. It ensures optimal and rapid charging of your leisure battery from the alternator while driving. This device supports various battery technologies, including classic lead-acid, lead-gel, lead-AGM, and modern LiFePO4 lithium batteries, offering selectable charging programs for unsupervised, fast, and gentle full charging from any state of charge.

Unlike simple cut-off relays, the VCC 1212-45 increases the charging voltage to the precise level required by each battery type, as specified by manufacturers, ensuring a complete charge. It effectively compensates for long charging cable losses and alternator voltage fluctuations, common in modern vehicles (e.g., Euro 6 with intelligent alternators). The intelligent microprocessor-controlled charging with IU1oU2oU3 characteristic curves and dynamic charging time calculation guarantees a quick, gentle, and full charge, maintaining the charge of connected batteries while simultaneously supplying power to 12V consumers.

2. Инструкции по технике безопасности

• Read this manual completely before installation and operation.
• Installation must be performed by qualified personnel in accordance with all applicable safety standards and regulations.
• Ensure all connections are secure and correctly polarized to prevent damage to the device or batteries.
• Перед выполнением любых работ по установке, техническому обслуживанию или устранению неполадок всегда отключайте источник питания.
• Не открывайте устройство casinг. Внутри нет деталей, подлежащих обслуживанию пользователем.
• Храните устройство вдали от влаги, экстремальных температур и легковоспламеняющихся материалов.
• Обеспечьте надлежащую вентиляцию вокруг зарядного устройства, чтобы предотвратить его перегрев.
• Use appropriate fuses as specified in the wiring diagram to protect the cables and the device.

3. Настройка и установка

3.1. Физическая установка

The VCC 1212-45 features a compact design and low weight due to high-frequency switching technology. Mount the unit in a dry, well-ventilated area, ensuring the rubber feet for vibration reduction are not removed. These feet are crucial for the device's longevity and performance.

3.2. Схема подключения

Refer to the diagram below for correct wiring. All fuses should be connected as directly as possible to the batteries for optimal cable protection.

Figure 1: General Connection Diagram for Votronic VCC 1212-45 Charger

• Battery II IN (Start): Connects to the Start Battery.
• Battery I OUT (Leisure): Connects to the Leisure Battery.
• D+ or Terminal 15: This signal must be connected for the charger to activate.
• Sense In + (Start) / Terminal 15/D+: Connect these small wires (0.5-1.5 mm²) to the respective terminals. Strip cable ends by 10 mm.
• Sense Out + (Leisure): Connect this small wire (0.5-1.5 mm²) to the leisure battery positive terminal. Strip cable ends by 10 mm.
• Предохранители:
• Fuse II (Start Battery): 30 A - 80 A.
• Fuse I (Leisure Battery): 30 A / 50 A.
• Small Fuses: 3 A for sense lines.
• Шасси заземление: Connect both start and leisure batteries to chassis ground.
• Объем ввода / выводаtage: The charger supports 12V input to 12V output, or 24V input to 12V output.

3.3 Выбор типа аккумулятора

Используйте Slide switch Battery-Type on the unit to select the appropriate charging program for your leisure battery (Lead-Acid, Lead-Gel, Lead-AGM, or LiFePO4). Refer to the device's labeling for specific switch positions.

3.4. Temperature Sensor Connection

Connect the supplied temperature sensor to the designated port on the charger. For LiFePO4 batteries, mount the temperature sensor on the negative terminal of the battery. This allows for automatic adaptation of charging voltage to battery temperature, optimizing charging efficiency and preventing unnecessary gassing in lead batteries, and protecting LiFePO4 batteries at low temperatures (below 0°C).

4. Операция

4.1. Автоматический режим работы.

The VCC 1212-45 operates fully automatically. Once connected, the device is activated by the alternator when the vehicle engine is running. When the engine is off, the batteries are not discharged. The charger continuously charges or maintains the battery even with simultaneous consumption, with charging times automatically calculated and monitored by the device.

4.2. Charging Characteristics

• Томtagе Регламент: Уровень зарядкиtage is free of spikes and regulated to prevent battery overcharging.
• Компенсация за потерю линии связи: The device fully compensates for line losses and alternator voltage fluctuations, ensuring stable charging.
• 12V Consumer Protection: Connected 12V consumers are protected against overvoltages и томtagе колебания.
• Deeply Discharged Lead Batteries: Supports gentle pre-charging of deeply discharged lead batteries up to 8V, then provides powerful support even with active consumers.

4.3. Функции защиты

The VCC 1212-45 offers multiple protections for unsupervised charging:

• Защита от перегрузки
• Защита от перегрева
• Оверволtagэлектронная защита
• Защита от короткого замыкания
• Incorrect behavior protection
• Battery discharge protection (electronic regulation up to complete separation of the device and battery)

Parallel operation with other charging sources on a single battery is possible without issues.

5. Техническое обслуживание

The VOTRONIC VCC 1212-45 charger is designed for maintenance-free operation. To ensure optimal performance and longevity, consider the following:

• Регулярный осмотр: Periodically check all cable connections for tightness and corrosion. Ensure fuses are intact.
• Уборка: Keep the device clean and free from dust and debris. Use a dry, soft cloth for cleaning. Do not use liquid cleaners or solvents.
• Вентиляция: Ensure that the ventilation openings are not obstructed to allow for proper heat dissipation.
• Условия окружающей среды: Operate the device within its specified temperature and humidity ranges.

6. Поиск Неисправностей

If the charger is not functioning as expected, perform the following basic checks before contacting support:

If the problem persists after performing these checks, please contact VOTRONIC customer support.

7. Технические характеристики

8. Информация о гарантии

VOTRONIC products are manufactured with high-quality materials and undergo strict quality control. This product comes with a standard manufacturer's warranty against defects in materials and workmanship. The warranty period typically begins from the date of purchase. Please retain your proof of purchase for warranty claims.

The warranty does not cover damages resulting from improper installation, misuse, unauthorized modifications, accidents, or normal wear and tear. For detailed warranty terms and conditions, please refer to the official VOTRONIC webсайт или свяжитесь с их службой поддержки.

9. Поддержка клиентов

For technical assistance, troubleshooting, or warranty inquiries, please contact VOTRONIC customer support. You can typically find contact information, including phone numbers and email addresses, on the official VOTRONIC webсайте или через вашего авторизованного дилера.

При обращении в службу поддержки, пожалуйста, подготовьте следующую информацию:

• Product Model: VCC 1212-45
• Дата покупки
• Описание проблемы
• Any troubleshooting steps already performed